Domestic Supply Consultations on Steel Derivative Goods
The Government of Canada is seeking input from Canadian producers and industry associations regarding their ability to produce a range of steel derivative products that are subject to surtaxes when imported.
Input to these consultations will be used to validate whether these products are made in Canada. If they are not made in Canada, the importers of these goods may be eligible for surtax relief.
Background
On December 26, 2025, the Government of Canada imposed a 25% surtax on certain steel derivative products imported from all countries under the Steel Derivative Goods Surtax Order. This measure was introduced in response to concerns of trade diversion of steel derivative products into the Canadian market and to support domestic industries.
The Government announced that requests for remission of surtaxes on steel derivative products will be considered on a case-by-case basis in the following instances:
- To address situations where goods used as inputs cannot be sourced domestically, either on a national or regional basis, or reasonably from other sources.
- To address, on a case-by-case basis, other exceptional circumstances that could have severe adverse impacts on the Canadian economy.
A key consideration in the government’s assessment of remission requests is whether the imported product can reasonably be sourced domestically.
Purpose of this Consultation
The Department of Finance Canada is consulting with Canadian producers to determine whether the products listed below can be sourced domestically.
If your company can produce any of the products listed in the table below, please indicate this by completing the web form.
If a Canadian supplier is identified, the company requesting tariff relief may be directed to contact that supplier in order to assess that their purchasing needs can be met (i.e., quantities, specifications, timelines).
This consultation is open until June 3, 2026 at 11:59pm PDT.
Additional supporting materials or questions can be sent to: remissions-trq-derivatives-remises-ct-produitsderives@fin.gc.ca.
For ease of reference, the following categories of goods are covered by this consultation:
- Prestressed strand
- Wire rope and cables
- Chains and parts
- Doors, windows and frames
- Bridge sections
- Fasteners
- Metal furniture
- Seats and chairs
- Springs
- Nails, tacks and staples
- Wire cloth, grill, netting and fencing
- Base metal fittings
- Garage door hardware
- Gate and door hardware
- Prefabricated buildings
- Other structures
- Other articles of iron or steel
- Articles of cast iron and steel
List of Products for Consultation
Below is a detailed list of the products subject to consultation, including their HS code and physical description.
New:
For some products, the appropriate HS code remains to be determined (TBD). In those instances, two potential HS codes have been included for consideration. However, only the most appropriate HS code would be included in the Order for remission, if approved.
| Product Code | HS Code | Category | Product Description (As described by the requestor, in the language in which it was received) |
|---|---|---|---|
| 1 | 7308.10.00 | Bridge sections | Steel stay cable anchorage assemblies of grade C45R + U, of specification EN 10083, EN 10210, EN 10204 and EN 10308, fabricated and assembled from hot rolled peeled steel bar, with an outer diameter of 185 mm, normalized, with tensile strength Rm exceeding 610 MPa, yield strength Rp0.2 exceeding 300 MPa, elongation at rupture A exceeding 12%, Class 2 ultrasound test classification, zinc aluminium coated with sealer |
| 2 | 7308.10.00 | Bridge sections | Steel stay cable anchorage assemblies of grade C45R + U, of specification EN 10083, EN 10210, EN 10204 and EN 10308, fabricated and assembled from hot rolled peeled steel bar, with an outer diameter of 185 mm and an adjustment range of 100 mm, normalized, with tensile strength Rm exceeding 610 MPa, yield strength Rp0.2 exceeding 300 MPa, elongation at rupture A exceeding 12%, Class 2 ultrasound test classification, zinc aluminium coated with sealer |
| 3 | 7308.10.00 | Bridge sections | Steel stay cable anchorage assemblies of grade C45R + U, of specification EN 10083, EN 10210, EN 10204 and EN 10308, fabricated and assembled from hot rolled peeled steel bar, with an outer diameter of 185 mm and an adjustment range of 200 mm, normalized, with tensile strength Rm exceeding 610 MPa, yield strength Rp0.2 exceeding 300 MPa, elongation at rupture A exceeding 12%, Class 2 ultrasound test classification, zinc aluminium coated with sealer |
| 4 | 7308.10.00 | Bridge sections | Steel stay cable anchorage assemblies of grade C45R + U, of specification EN 10083, EN 10210, EN 10204 and EN 10308, fabricated and assembled from hot rolled peeled steel bar, with an outer diameter of 185 mm and an adjustment range of 300 mm, normalized, with tensile strength Rm exceeding 610 MPa, yield strength Rp0.2 exceeding 300 MPa, elongation at rupture A exceeding 12%, Class 2 ultrasound test classification, zinc aluminium coated with sealer |
| 5 | 7308.10.00 | Bridge sections | Steel expansion tubes of grade TU E235A, of specification EN 10297-1 and EN ISO 1461, fabricated, with a wall thickness of 4 mm and a length of 700 mm, galvanized |
| 6 | 7308.10.00 | Bridge sections | Steel expansion tubes of grade TU E235A, of specification EN 10297-1 and EN ISO 1461, fabricated, with a wall thickness of 4 mm and a length of 800 mm, galvanized |
| 7 | 7308.10.00 | Bridge sections | Steel protection tubes of grade TU E235A, of specification EN 10297-1 and EN ISO 1461, fabricated, with a wall thickness of 4 mm, galvanized |
| 8 | 7308.10.00 | Bridge sections | Steel stay cable anchorage assemblies (EN 10083, C45R+U), from hot-rolled peeled bar, zinc aluminium coated, for cable-stayed bridge construction |
| 9 | 7308.10.00 | Bridge sections | Steel expansion tubes and protection tubes (TU E235A, EN 10297-1), galvanized, for bridge stay cable protection |
| 10 | 7308.30.00.10 | Doors, windows, and frames | Unfinished steel frame sections (sash, casement, or frame profiles) as raw input for door and window fabrication |
| 11 | 7308.30.00.21 | Doors, windows, and frames | Commercial and industrial sliding steel doors and frames: warehouse doors, hangar doors, cold storage doors, fire-rated sliding doors |
| 12 | 7308.30.00.22 | Doors, windows, and frames | Residential steel garage doors and frames: sectional overhead, single-panel, and insulated residential garage doors |
| 13 | 7308.30.00.29 | Doors, windows, and frames | Commercial steel access doors and panels: utility access doors, duct access panels, ceiling hatches |
| 14 | 7308.30.00.29 | Doors, windows, and frames | Blast-resistant doors, vault doors, and ballistic-rated steel doors for high-security and critical infrastructure applications |
| 15 | 7308.30.00.29 | Doors, windows, and frames | Standard fire-rated hollow metal doors and frames for commercial construction (e.g. Steelcraft/Allegion type) |
| 16 | 7308.30.00.30 | Doors, windows, and frames | Architectural and heritage-style steel windows: hot-rolled steel profiles for heritage restoration and high-end architectural glazing |
| 17 | 7308.30.00.30 | Doors, windows, and frames | Commercial and industrial steel-framed windows: factory windows, fire-rated windows, fixed-lite and operable steel window systems |
| 18 | 7308.30.00.40 | Doors, windows, and frames | Steel door thresholds: commercial entrance thresholds, ADA-compliant thresholds, thermal-break thresholds |
| 19 | 7308.90.00 | Other structures | Welded carbon steel ornamental fence panels and gate panels, 3-rail flat top design; steel grade: ASTM A513 Type 5 (electric resistance welded mechanical tubing) or ASTM A500 Grade B (cold-formed welded structural tubing); construction: welded; panel: 92" W x 48" H and 92" W x 60" H (2,337 x 1,219 mm and 2,337 x 1,524 mm); gates: 34" to 46" W x 48" to 60" H (864-1,168 mm W x 1,219-1,524 mm H); wall thickness: 16 ga (1.61 mm); coating: black powder coat, minimum 2.0–3.5 mil DFT, TGIC polyester. Square steel line posts: 2" x 2" x 16 ga (50.8 x 50.8 x 1.61 mm), lengths 7, 8, 9 ft (2,134–2,743 mm); steel grade: ASTM A500 Grade B; construction: welded; coating: black powder coat. |
| 20 | 7308.90.00.99 | Other structures | Malleable cast iron slip-on pipe clamp fittings of grade BS 340/12 equivalent or grade 420/12 equivalent, produced by malleable iron casting, non-threaded, with nominal pipe diameters of 0.75 inch, 1 inch, 1.25 inch, 1.5 inch or 2 inch, including pre-installed set screws, fluorocarbon coated |
| 21 | 7308.90.00.99 | Other structures | Forged low-alloy steel integral wellhead casing spool of grade AISI 4130 / UNS G41300 of specification API 6A PSL-3, API 20B or API 20C and NACE MR0175 / ISO 15156, electric-furnace melted, forged, normalized, quenched and tempered, with an outer diameter of 584 mm, an overall length of 670 mm, a through-bore diameter of 276 mm, a weight of 623 kg (1,374 lb), with 279 mm studded flange top and bottom connections and two 52 mm studded side outlets, no surface coating |
| 22 | 7308.90.00.99 | Other structures | Forged low-alloy steel oilfield tubing head of grade AISI 4130 / UNS G41300 of specification API 6A PSL-1, API 20B or API 20C and NACE MR0175 / ISO 15156, electric-furnace melted, forged, normalized, quenched and tempered, with a through-bore diameter of 164 mm (6.45 inches), an overall length of 359 mm (14.12 inches), with a 179 mm (7-1/16 inch) flange top connection, a 178 mm slip-on-weld bottom connection and two 51 mm threaded side outlets, semi-finished, no surface coating |
| 23 | 7308.90.00.99 | Other structures | Forged low-alloy steel oilfield tubing head assembly with offset bore and angled outlet configuration of grade AISI 4130 / UNS G41300 of specification API 6A, API 20B or API 20C and NACE MR0175 / ISO 15156, electric-furnace melted, forged, normalized, quenched and tempered, with a 279 mm (11 inch) studded flange bottom connection, a 179 mm (7-1/16 inch) flange top connection positioned on a 36 mm (1.40 inch) offset centreline and two 52 mm (2-1/16 inch) studded side outlets, semi-finished, no surface coating |
| 24 | 7308.90.00.99 | Other structures | Forged low-alloy steel oilfield tubing head with metal-to-metal slip-lock seal lower connection of grade AISI 4130 / UNS G41300 of specification API 6A PSL-2, API 20B or API 20C and NACE MR0175 / ISO 15156, electric-furnace melted, forged, normalized, quenched and tempered, with a through-bore diameter of 226 mm (8.88 inches), an overall length of 422 mm (16.62 inches), with a 279 mm (11 inch) flange top connection, a 244 mm (9-5/8 inch) outside-engagement metal-seal lower connection and two 52 mm (2-1/16 inch) extended-flange side outlets, semi-finished, externally treated with manganese or zinc phosphate conversion coating |
| 25 | 7308.90.00.99 | Other structures | Forged low-alloy steel oilfield tubing head assembly with offset upper bore and integrated secondary tubing head outlet of grade AISI 4130 / UNS G41300 of specification API 6A, API 20B or API 20C and NACE MR0175 / ISO 15156, electric-furnace melted, forged, normalized, quenched and tempered, with a 279 mm (11 inch) studded flange bottom connection, a 179 mm (7-1/16 inch) flange top connection on a 30 mm (1.188 inch) offset centreline, one 79 mm (3-1/8 inch) secondary tubing head outlet inclined 9 degrees with metal-to-metal seal profile and two 52 mm (2-1/16 inch) extended-flange side outlets, semi-finished, externally treated with phosphate conversion coating |
| 26 | 7308.90.00.99 | Other structures | Steel frame skids of grade 50, of specification ASTM A572/A572M-21 or ASTM A992, hot-rolled, fabricated from wide flange sections and formed plate, with a width of 8 feet, with a length of at least 8 feet but not exceeding 40 feet and with a height of 6 inches, uncoated |
| 27 | 7308.90.00.99 | Other structures | Low-carbon steel shipping racks fabricated from steel tubes of specification ASTM A501, hot-rolled, with tube dimensions of 2 inches by 2 inches, with a wall thickness of 0.19 inches, with a width of 6 feet, with a length of 5 feet and with a height of 5 feet, powder coated |
| 28 | 7308.90.00.99 | Other structures | Carbon steel posts for high tension cable barrier systems, of specification AASHTO M270, of grade ASTM A36 or ASTM A572, formed and machined, with a cross-section of 75 mm by 59 mm and with a length of at least 1,524 mm but not exceeding 1,804 mm, with a cross-section of 100 mm by 68 mm and with a length of 1,200 mm, or with a cross-section of 64 mm by 83 mm and with a length of at least 1,219 mm but not exceeding 1,448 mm, hot-dip galvanized to ASTM A123 |
| 29 | 7308.90.00.99 | Other structures | Carbon steel cable splice assemblies for 3x7 wire rope, consisting of forged splice body, threaded rods and nuts, of grade ASTM A572, AISI 1045, ASTM F1554 Grade 55, ASTM F1554 Grade 105, ASTM A563 or ASTM A194, of specification ASTM A741, forged and stamped, case-hardened, with a splice body diameter of at least 64 mm, with a length of at least 191 mm but not exceeding 991 mm, galvanized to ASTM A153 |
| 30 | 7308.90.00.99 | Other structures | Carbon steel sleeves for high tension cable barrier systems, of grade ASTM A500 Grade B, of specification AASHTO M270, formed and machined, with a cross-section of 127 mm by 83 mm and with a length of 781 mm, with a cross-section of 102 mm by 76 mm and with a length of 781 mm, or with a cross-section of 76 mm by 102 mm and with a length of 1,067 mm, hot-dip galvanized to ASTM A123 |
| 31 | 7308.90.00.99 | Other structures | Carbon steel bar grating panels of grade A36, of specification ANSI/NAAMM MBG 531 or MBG 532, with a smooth or serrated surface, with a bearing bar depth of at least 0.75 inches but not exceeding 4 inches, with a bearing bar thickness of at least 0.125 inches but not exceeding 0.375 inches, with a bearing bar spacing of 19/16 inches and with a cross bar spacing of 2 inches or 4 inches, with a width of at least 2 feet but not exceeding 3 feet and with a length of at least 20 feet but not exceeding 24 feet, bare or hot-dip galvanized to ASTM A123 |
| 32 | 7308.90.00.99 | Other structures | Stainless steel bar grating panels of grade 304 or 316 of specification ASTM A240 and ANSI/NAAMM MBG 531, with a smooth or serrated surface, with a bearing bar depth of at least 1 inch but not exceeding 2 inches, with a bearing bar thickness of at least 0.125 inches but not exceeding 0.187 inches, with a bearing bar spacing of 19/16 inches and with a cross bar spacing of 4 inches, with a width of 3 feet and with a length of at least 20 feet but not exceeding 24 feet, mill finish or electropolished |
| 33 | 7308.90.00.99 | Other structures | Carbon steel bar grating treads of grade A36, of specification ANSI/NAAMM MBG 531, with a bearing bar depth of 1.25 inches, with a bearing bar thickness of 0.187 inches, with a smooth or serrated surface, with checker plate nosing, with a depth of at least 9 3/4 inches but not exceeding 12 1/8 inches and with a width of at least 24 inches but not exceeding 48 inches, bare or hot-dip galvanized to ASTM A123 |
| 34 | 7308.90.00.99 | Other structures | Carbon steel or stainless steel (grade 316) channel grating end plates, of specification ASTM A1008 or ASTM A240, with a thickness of at least 3/16 inches but not exceeding 1/4 inch, with a width of at least 1 1/2 inches but not exceeding 2 inches and with a length of at least 4 3/4 inches but not exceeding 12 inches, with round hole of 7/16 inch and slot hole of 7/16 inch by 1 3/8 inches, galvanized to ASTM A123 or electropolished |
| 35 | 7308.90.00.99 | Other structures | Carbon steel bar grating panels, ANSI/NAAMM MBG 531/532, bare or hot-dip galvanized (ASTM A123), for industrial flooring, platforms, and walkways |
| 36 | 7308.90.00.99 | Other structures | Stainless steel bar grating panels (grade 304 or 316), mill or electropolished finish, for food processing, pharmaceutical, and corrosive environments |
| 37 | 7308.90.00.99 | Other structures | Carbon or stainless steel bar grating stair treads and end plates, for industrial stairways, mezzanines, and access platforms |
| 38 | 7308.90.00.99 | Other structures | Forged low-alloy steel wellhead components (casing spools, tubing heads), AISI 4130, API 6A, NACE MR0175, for oil and gas well completions |
| 39 | 7308.90.00.99 | Other structures | Fabricated steel frame skids (ASTM A572/A992), hot-rolled wide-flange sections and formed plate, for modular equipment mounting and transportation |
| 40 | 7308.90.00.99 | Other structures | Welded carbon steel ornamental fence panels and gate panels (ASTM A500/A513), 2 or 3-rail design, powder coated, with posts |
| 41 | 7308.90.00.99 | Other structures | Malleable cast iron slip-on pipe clamp fittings, non-threaded, for structural pipe frameworks, handrails, and modular pipe construction |
| 42 | 7312.10.00 | Wire rope and cables | Wire rope with fiber core, regular lay, with a diameter of at least 0.625 inches but not exceeding 1.000 inch, galvanized, with construction variants (6x19, 6x24, 6x26) Manufactured in accordance with ISO 2408, RR-W-410G. G1770, G2160 & G1960 |
| 43 | 7312.10.00 | Wire rope and cables | Wire rope with wire core, regular lay, with a diameter of at least 0.625 inches but not exceeding 1.000 inch, galvanized, with construction variants (6x19, 6x24, 6x26) Manufactured in accordance with ISO 2408, RR-W-410G. G1770, G2160 & G1960 |
| 44 | 7312.10.00 | Wire rope and cables | Steel wire rope composed of multiple wires twisted into strands and helically wound around a synthetic core, drawn, preformed and closed, of 5 x 19, 5 x 26, 4 x 26 or 4 x 36 construction, with a diameter of 6.5 mm, 8.3 mm, 9.5 mm, 10 mm, 11.5 mm, 14 mm or 16 mm, galvanized |
| 45 | 7312.10.00 | Wire rope and cables | Galvanized steel wire rope of grade extra improved plow steel (EIPS) of specification EN 12385-4 processed by stranding in 6×26 Warrington Seale construction with independent wire rope core and right-hand regular lay with a diameter of 2 inches (50.8 mm) and with a length of 2600 feet (793 meters) lubricated |
| 46 | 7312.10.00.22 | Prestressed strand | Stranded wire of non-alloy steel of specification ASTM A416, cold-drawn, stress-relieved, of grade 270, consisting of seven wires helically wound with one central wire and six outer wires, with a nominal diameter of at least 9.3 mm but not exceeding 15.2 mm, uncoated or epoxy-coated or galvanized |
| 47 | 7312.10.00.22 | Prestressed strand | Stranded wire of non-alloy steel of specification ASTM A416, cold-drawn, stress-relieved, of grade 270, consisting of seven wires helically wound with one central wire and six outer wires, with a diameter of 12.7 mm, uncoated or epoxy-coated or galvanized |
| 48 | 7312.10.00.22 | Prestressed strand | Stranded wire of non-alloy steel of specification ASTM A416, cold-drawn, stress-relieved, of grade 270, consisting of seven wires helically wound with one central wire and six outer wires, with a diameter of 15.2 mm, uncoated or epoxy-coated or galvanized |
| 49 | 7312.10.00.22 | Prestressed strand | Stranded wire of non-alloy steel of specification A416/A416M-17a, of grade 270, of a diameter exceeding 5mm |
| 50 | 7312.10.00.22 | Prestressed strand | Non-alloy steel prestressed strand composed of seven helically wound wires, including six outer wires laid over a single central core wire, low-relaxation, of grade 270, of specification ASTM A416/A416M, with an ultimate tensile strength of 1860 MPa, with a diameter of at least 9 mm but not exceeding 18 mm, uncoated |
| 51 | 7312.10.00.22 | Prestressed strand | Non-alloy steel prestressed strand composed of seven helically wound wires, including six outer wires laid over a single central core wire, low-relaxation, of specification ASTM A416/A416M, with a diameter of at least 9.53 mm but not exceeding 12.7 mm, uncoated |
| 52 | 7312.10.00.22 | Prestressed strand | Prestressed concrete strand of non-alloy steel, 7-wire helical construction, ASTM A416 Grade 270, low-relaxation, for post-tensioning and pre-tensioning in bridge, building, and infrastructure construction |
| 53 | 7312.10.00.31 | Wire rope and cables | High carbon steel stranded wire ropes of grade 220, of specification modified EN 10138 Class A, stranded in 1x7 construction, cold drawn and stress relieved, with a diameter of 0.3125 inches and a reel length of 8500 feet, galvanized with a coating mass not exceeding 60 g/m2 |
| 54 | 7312.10.00.31 | Wire rope and cables | High carbon steel stranded wire ropes of grade 220, of specification modified EN 10138 Class A, stranded in 1x7 construction, cold drawn and stress relieved, with a diameter of 0.3125 inches and a reel length of 6000 feet, galvanized with a coating mass not exceeding 60 g/m2 |
| 55 | 7312.10.00.31 | Wire rope and cables | High carbon steel stranded wire ropes of grade 220, of specification modified EN 10138 Class A, stranded in 1x7 construction, cold drawn and stress relieved, with a diameter of 0.375 inches and a reel length of 7000 feet, galvanized with a coating mass not exceeding 60 g/m2 |
| 56 | 7312.10.00.31 | Wire rope and cables | High carbon steel stranded wire ropes of grade EIPS, of specification EN 12385, stranded in 6x19 class FC construction with fiber core, spheroidized annealed, with a diameter of 0.625 inches and a length of 5000 feet, galvanized |
| 57 | 7312.10.00.31 | Wire rope and cables | High carbon steel stranded wire ropes of grade EIPS, of specification EN 12385, stranded in 6x19 class FC construction with fiber core, spheroidized annealed, with a diameter of 0.75 inches and a length of 5000 feet, galvanized |
| 58 | 7312.10.00.31 | Wire rope and cables | High carbon steel stranded wire ropes of grade EIPS, of specification EN 12385, stranded in 6x19 class FC construction with fiber core, spheroidized annealed, with a diameter of 0.875 inches and a length of 5000 feet, galvanized |
| 59 | 7312.10.00.31 | Prestressed strand | High carbon steel stranded wire ropes of specification AASHTO M30 and ASTM A741, 3x7 stranded, preformed, right regular lay, factory pre-stretched, with a diameter of 0.75 inches and with a length of 600 m or 1,200 m, galvanized to Type 1 Class A |
| 60 | 7312.10.00.31 | Wire rope and cables | Stainless steel wire cable of grade 304, 7x7 construction (7 strands of 7 wires), with an outer diameter of at least 0.09375 inches but not exceeding 0.125 inches and with a length of at least 104 inches but not exceeding 150 inches, with or without swaged loop, polished or unpolished |
| 61 | 7312.10.00.31 | Wire rope and cables | Stainless steel wire cable of grade 304, 7x19 construction (7 strands of 19 wires), with an outer diameter of 0.15625 inches and with a length of 259.75 inches, with swaged loop, polished |
| 62 | 7312.10.00.31 | Wire rope and cables | New swage compacted, stranded steel wire rope, 4-strand semi-rotation-resistant construction, K4xK36-FC, bright or galvanized finish, nominal diameter not over 25 mm, Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 63 | 7312.10.00.31 | Wire rope and cables | New strand compacted stranded steel wire rope, 6-strand, 6xk31 WS or 6xK36 WS construction, fibre core or independent wire rope core, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 64 | 7312.10.00.31 | Wire rope and cables | New stranded steel wire rope, 6-strand, 6x19 Seale or 6x26 WS construction, fibre core or independent wire rope core, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 65 | 7312.10.00.31 | Wire rope and cables | New stranded steel wire rope, 6-strand, 6x36 WS construction, fibre core, bright or galvanized finish, nominal diameter not over 25 mm; Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 66 | 7312.10.00.31 | Wire rope and cables | New stranded steel wire rope, 6-strand, 6x36 WS construction, independent wire rope core, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength Grade: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 67 | 7312.10.00.31 | Wire rope and cables | New swaged stranded steel wire rope, 6-strand, K6x31WS-IWRC or K6x36WS-IWRC construction, bright or galvanized finish, nominal diameter not over 25 mm;Tensile Strength Grade: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M or DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 68 | 7312.10.00.31 | Wire rope and cables | New stranded galvanized aircraft cable, 7x7 or 7x19 construction, nominal diameter not over 25 mm; Tensile Strength Grade: EIPS(1960); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 69 | 7312.10.00.31 | Wire rope and cables | New strand compacted, stranded steel wire rope, 8-strand, 8xK19S-PWRC(K) or 8xK26WS-PWRC(K) construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 70 | 7312.10.00.31 | Wire rope and cables | New stranded steel wire rope, 8-strand, 8x19S-IWRC, 8x25F-IWRC, 8x26WS-IWRC, 8x31WS-IWRC, 8x36WS-IWRC or 8x41WS-IWRC construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 71 | 7312.10.00.31 | Wire rope and cables | New stranded steel wire rope, 8-strand, 8x25F-EPIWRC, 8x36WS-EPIWRC or 8x41WS-EPIWRC construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 72 | 7312.10.00.31 | Wire rope and cables | New strand compacted, stranded steel wire rope, 8-strand, 8xK19S-EPIWRC, 8xK26WS-EPIWRC, 8xK31WS-EPIWRC, 8xK36WS-EPIWRC or 8xK41WS-EPIWRC construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 73 | 7312.10.00.31 | Wire rope and cables | New stranded steel wire rope, 8-strand, 8xK19S-IWRC or 8x36WS-IWRC construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 74 | 7312.10.00.31 | Wire rope and cables | New strand compacted, stranded steel wire rope, 8-strand, 8xK26WS-PWRC(K)(EP), 8xK31WS-PWRC(K)(EP), 8xK36WS-PWRC(K)(EP) or 8xK41WS-PWRC(K)(EP) construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 75 | 7312.10.00.31 | Wire rope and cables | New strand compacted, stranded steel wire rope, 8-strand, 8xK31WS-IWRC construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 76 | 7312.10.00.31 | Wire rope and cables | New swage compacted, stranded steel wire rope, 8-strand, K8x25F-EPIWRC construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 77 | 7312.10.00.31 | Wire rope and cables | New swage compacted, stranded stainless steel wire rope, 4 outer strands, K4x19S-SFC construction, Stainless Steel Type AISI 304 - 1.4301, nominal diameter not over 25 mm; Tensile Strength: 1570-1770; Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 78 | 7312.10.00.31 | Wire rope and cables | New stranded stainless steel aircraft cable, 7-strand, 7x7 or 7X19 construction, Stainless Steel Type 304 or 316, nominal diameter not over 25 mm; Tensile Strength 1550 - 2210; Specification: RR-W-410; supplied on reels or cut lengths. |
| 79 | 7312.10.00.31 | Wire rope and cables | New stranded stainless steel wire rope, 6-strand, 6x36 WS construction, independent wire rope core, Stainless Steel Type 304 or 316, nominal diameter not over 25 mm; Tensile Strength 1550 - 2210; Specification: RR-W-410; supplied on reels or cut lengths. |
| 80 | 7312.10.00.31 | Wire rope and cables | Galvanized carbon steel wire rope of grade IPS (Improved Plow Steel) or EIP (Extra Improved Plow Steel), of specification FS-RR-W410J or ASTM A1023, 6x19 construction with fibre core or independent wire rope core, preformed, right hand regular lay, with a diameter of at least 1/2 inch but not exceeding 3/4 inch, with a length of at least 2,400 feet but not exceeding 3,600 feet, heavy galvanized, lubricated |
| 81 | 7312.10.00.31 | Wire rope and cables | Ropes and cables, containing not more than eight strands, new, of a diameter not exceeding 25 mm |
| 82 | 7312.10.00.31 | Wire rope and cables | Stainless steel wire rope, 6-strand construction (6x19, 6x26, 6x36 WS), fiber or wire core, for marine, food processing, architectural, and corrosion-resistant applications |
| 83 | 7312.10.00.32 | Wire rope and cables | New swage compacted, stranded steel wire rope, 4-strand semi-rotation-resistant construction, K4xK36-FC, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 84 | 7312.10.00.32 | Wire rope and cables | New strand compacted stranded steel wire rope, 6-strand, 6xk31 WS or 6xK36 WS construction, fibre core or independent wire rope core, bright or galvanized finish, over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 85 | 7312.10.00.32 | Wire rope and cables | New stranded steel wire rope, 6-strand, 6x19 Seale or 6x26 WS construction, fibre core or independent wire rope core, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 86 | 7312.10.00.32 | Wire rope and cables | New stranded steel wire rope, 6-strand, 6x36 WS construction, fibre core, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 87 | 7312.10.00.32 | Wire rope and cables | New stranded steel wire rope, 6-strand, 6x36 WS construction, independent wire rope core, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 88 | 7312.10.00.32 | Wire rope and cables | New swaged stranded steel wire rope, 6-strand, K6x31WS-IWRC or K6x36WS-IWRC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M or DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 89 | 7312.10.00.32 | Wire rope and cables | New stranded steel wire rope, 8-strand, 8x19S-IWRC, 8x25F-IWRC, 8x26WS-IWRC, 8x31WS-IWRC, 8x36WS-IWRC or 8x41WS-IWRC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 90 | 7312.10.00.32 | Wire rope and cables | New stranded steel wire rope, 8-strand, 8x25F-EPIWRC, 8x36WS-EPIWRC or 8x41WS-EPIWRC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 91 | 7312.10.00.32 | Wire rope and cables | New strand compacted, stranded steel wire rope, 8-strand, 8xK19S-EPIWRC, 8xK26WS-EPIWRC, 8xK31WS-EPIWRC, 8xK36WS-EPIWRC or 8xK41WS-EPIWRC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: IPS (1770), EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 92 | 7312.10.00.32 | Wire rope and cables | New stranded steel wire rope, 8-strand, 8xK19S-IWRC or 8x36WS-IWRC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 93 | 7312.10.00.32 | Wire rope and cables | New strand compacted, stranded steel wire rope, 8-strand, 8xK26WS-PWRC(K)(EP), 8xK31WS-PWRC(K)(EP), 8xK36WS-PWRC(K)(EP) or 8xK41WS-PWRC(K)(EP) construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 94 | 7312.10.00.32 | Wire rope and cables | New strand compacted, stranded steel wire rope, 8-strand, 8xK31WS-IWRC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 95 | 7312.10.00.32 | Wire rope and cables | New swage compacted, stranded steel wire rope, 8-strand, K8x25F-EPIWRC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 96 | 7312.10.00.32 | Wire rope and cables | New stranded stainless steel wire rope, 6-strand, 6x36 WS construction, independent wire rope core, Stainless Steel Type 304 or 316, nominal diameter over 25 mm but not over 50 mm; Tensile Strength 1410 - 2450; Specification: RR-W-410; supplied on reels or cut lengths. |
| 97 | 7312.10.00.32 | Wire rope and cables | Ropes and cables, containing not more than eight strands, new, of a diameter exceeding 25 mm but not exceeding 50 mm |
| 98 | 7312.10.00.33 | Wire rope and cables | Alloy steel and carbon steel 8-strand plasticated wire rope of wire grade C82D of specification EN ISO 16120-2, of rope grade 1960 of specification EN 12385-4, quenched and tempered, with swaged ferrule end fittings and pulling loops, with a minimum tensile strength of 1,770 N/mm², with a rope diameter of at least 64 mm but not exceeding 70 mm, with a total length of at least 49.54 m but not exceeding 116.02 m, with a maximum breaking load of at least 321 tonnes but not exceeding 385 tonnes, plastic impregnated |
| 99 | 7312.10.00.33 | Wire rope and cables | New stranded steel wire rope, 6-strand, 6x36 WS, 6x41 WS or 6 x 49 WS construction, independent wire rope core, bright or galvanized finish, nominal diameter over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 100 | 7312.10.00.33 | Wire rope and cables | New stranded steel wire rope, 8-strand, 8x19S-IWRC, 8x25F-IWRC, 8x26WS-IWRC, 8x31WS-IWRC, 8x36WS-IWRC or 8x41WS-IWRC construction, bright or galvanized finish, nominal diameter over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 101 | 7312.10.00.33 | Wire rope and cables | New stranded steel wire rope, 8-strand, 8x25F-EPIWRC, 8x36WS-EPIWRC or 8x41WS-EPIWRC construction, bright or galvanized finish, nominal diameter over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 102 | 7312.10.00.33 | Wire rope and cables | New strand compacted, stranded steel wire rope, 8-strand, 8xK19S-EPIWRC, 8xK26WS-EPIWRC, 8xK31WS-EPIWRC, 8xK36WS-EPIWRC or 8xK41WS-EPIWRC construction, bright or galvanized finish, nominal diameter over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 103 | 7312.10.00.33 | Wire rope and cables | New strand compacted, stranded steel wire rope, 8-strand, 8xK26WS-PWRC(K)(EP), 8xK31WS-PWRC(K)(EP), 8xK36WS-PWRC(K)(EP) or 8xK41WS-PWRC(K)(EP) construction, bright or galvanized finish, nominal diameter over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 104 | 7312.10.00.33 | Wire rope and cables | Ropes and cables, containing not more than eight strands, new, of a diameter exceeding 50 mm |
| 105 | 7312.10.00.41 | Wire rope and cables | Stainless steel armoured cables of chromium-nickel alloy core wrapped with stainless steel chromium armour, with a diameter of 5.4 mm, 6.4 mm, 7.0 mm, 7.4 mm or 9.0 mm |
| 106 | 7312.10.00.41 | Wire rope and cables | New swage compacted, stranded steel wire rope, 10 outer strands, category III rotation-resistant,K10x19S-EPIWRC construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 107 | 7312.10.00.41 | Wire rope and cables | New strand compacted, stranded steel wire rope, 10 outer strands, 10xK31WS-EPIWRC(K) construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 108 | 7312.10.00.41 | Wire rope and cables | New swage compacted, stranded steel wire rope, 10 outer strands, K10x19S-PWRC or K10x25F-PWRC construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 109 | 7312.10.00.41 | Wire rope and cables | New stranded steel wire rope, 12 outer strands, category II rotation-resistant,17x7 WSC, 18x7 WSC, 19x7-WSC, 18x19 WSC, or 19x19 WSC, construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 110 | 7312.10.00.41 | Wire rope and cables | New stranded steel wire rope, 16 outer strands, category I rotation-resistant, 29(W)xK7-KWSC construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 111 | 7312.10.00.41 | Wire rope and cables | New strand compacted, stranded steel wire rope, 18 total strands, category II rotation-resistant, 18 x K19-KWSC construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 112 | 7312.10.00.41 | Wire rope and cables | New strand compacted, stranded steel wire rope, 35 total strands, category I rotation-resistant, 35(W) x K7-KWSC, 35(W) x K17S-KWSC, 35(W) x K19W-KWSC or 35(W) x K25F-KWSC construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 113 | 7312.10.00.41 | Wire rope and cables | New stranded steel wire rope, 9 outer strands, 9x19S-PWRC or 9x25F-PWRC construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 114 | 7312.10.00.41 | Wire rope and cables | New swage compacted, stranded steel wire rope, 9 outer strands, K9x19S-PWRC or K9x25F-PWRC construction, bright or galvanized finish, nominal diameter not over 25 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 115 | 7312.10.00.41 | Wire rope and cables | New stranded stainless steel wire rope, 12 outer strands, category II rotation-resistant, 19x7-WSC, construction, stainless steel Type 304, nominal diameter not over 25 mm; Tensile Strength: 1550 - 2450; Specification: RR-W-410; supplied on reels or cut lengths. |
| 116 | 7312.10.00.41 | Wire rope and cables | Ropes and cables, containing more than eight strands, new, of a diameter not exceeding 25 mm |
| 117 | 7312.10.00.41 | Wire rope and cables | Galvanized carbon steel wire rope, 6-strand and 8-strand construction, fiber or wire core, ASTM A1023, for general lifting, rigging, cranes, hoisting, and industrial applications |
| 118 | 7312.10.00.41 | Wire rope and cables | Multi-strand rotation-resistant wire rope (9 to 35-strand construction), compacted or swaged, for tower cranes, mobile cranes, mine hoists, and deep shaft applications |
| 119 | 7312.10.00.41 | Prestressed strand | High-carbon steel stranded wire, 3x7 construction, preformed, AASHTO M30/ASTM A741, for highway median cable barrier systems |
| 120 | 7312.10.00.41 | Wire rope and cables | Stainless steel aircraft cable, 7x7 and 7x19 construction, for architectural tensioning, railing systems, display rigging, and light-duty applications |
| 121 | 7312.10.00.42 | Wire rope and cables | New swage compacted, stranded steel wire rope, 10 outer strands, category III rotation-resistant, K10x19S-EPIWRC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 122 | 7312.10.00.42 | Wire rope and cables | New strand compacted, stranded steel wire rope, 10 outer strands, 10xK31WS-EPIWRC(K) construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 123 | 7312.10.00.42 | Wire rope and cables | New swage compacted, stranded steel wire rope, 10 outer strands, K10x19S-PWRC or K10x25F-PWRC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 124 | 7312.10.00.42 | Wire rope and cables | New stranded steel wire rope, 12 outer strands, category II rotation-resistant, 17x7 WSC, 18x7 WSC, 19x7-WSC, 18x19 WSC, or 19x19 WSC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths. |
| 125 | 7312.10.00.42 | Wire rope and cables | New stranded steel wire rope, 16 outer strands, category I rotation-resistant, 29(W)xK7-KWSC or 29(W)xK17S construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 126 | 7312.10.00.42 | Wire rope and cables | New strand compacted, stranded steel wire rope, 18 total strands, category II rotation-resistant, 18 x K19-KWSC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 127 | 7312.10.00.42 | Wire rope and cables | New strand compacted, stranded steel wire rope, 35 total strands, category I rotation-resistant, 35(W) x K7-KWSC, 35(W) x K17S-KWSC, 35(W) x K19W-KWSC or 35(W) x K25F-KWSC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 128 | 7312.10.00.42 | Wire rope and cables | New stranded steel wire rope, 9 outer strands, 9x19S-PWRC or 9x25F-PWRC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 129 | 7312.10.00.42 | Wire rope and cables | New swage compacted, stranded steel wire rope, 9 outer strands, K9x19S-PWRC or K9x25F-PWRC construction, bright or galvanized finish, nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 130 | 7312.10.00.42 | Wire rope and cables | Ropes and cables, containing more than eight strands, new, of a diameter exceeding 25 mm but not exceeding 50 mm |
| 131 | 7312.10.00.43 | Wire rope and cables | New strand compacted, stranded steel wire rope, 10 outer strands, 10xK31WS-EPIWRC(K) construction, bright or galvanized finish, nominal diameter over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 132 | 7312.10.00.43 | Wire rope and cables | New strand compacted, stranded steel wire rope, 35 total strands, category I rotation-resistant, 35(W) x K7-KWSC, 35(W) x K17S-KWSC, 35(W) x K19W-KWSC or 35(W) x K25F-KWSC construction, bright or galvanized finish, nominal diameter over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 133 | 7312.10.00.43 | Wire rope and cables | New stranded steel wire rope, 16 outer strands, category I rotation-resistant, 29(W) x K17S-KWSC, 29(W) x K19W-KWSC or 29(W) x K25F-KWSC construction, bright or galvanized finish, nominal diameter over 50 mm; Tensile Strength: EIPS(1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths. |
| 134 | 7312.10.00.43 | Wire rope and cables | Ropes and cables, containing more than eight strands, new, of a diameter exceeding 50 mm |
| 135 | 7312.10.00.50 | Wire rope and cables | Carbon steel wire rope for forestry and logging: haulback lines, mainlines, skidder winch lines, guylines, 6-strand EIPS/EEIPS construction |
| 136 | 7313.00.00 | Other articles of iron or steel | Carbon steel barbed wire of specification ASTM A121, twisted double-strand construction with 4-point barbs, Grade 1 with a minimum tensile strength of 483 MPa, with a wire gauge of at least 15.5 gauge (1.83 mm) but not exceeding 12 gauge (2.67 mm), with a barb spacing of at least 75 mm but not exceeding 100 mm, in coils of 402 m, hot-dip galvanized to Class 3 |
| 137 | 7313.00.00 | Other articles of iron or steel | Barbed wire (single or double strand) for agricultural fencing and property delineation |
| 138 | 7313.00.00 | Other articles of iron or steel | Barbed tape (razor wire), concertina wire, and twisted flat wire for perimeter security and military/institutional applications |
| 139 | 7314.12.00 | Wire cloth, grill, netting and fencing | Industrial continuous-loop (endless) wire mesh belts for machinery: conveyor belts, filtration screens, heat-treatment belts, of stainless steel |
| 140 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven stainless steel wire cloth (mesh), of cold-drawn stainless steel wire of grade AISI 304 and/or AISI 316, produced using plain weave, twill weave or Dutch weave (including reverse Dutch), with a wire diameter of at least 0.025 mm but not exceeding 0.500 mm, with a mesh count of at least 20 but not exceeding 400 wires per inch, with a mesh count tolerance of ±2%, with a width of at least 24 inches but not exceeding 60 inches, cleaned and degreased, in rolls or slit strips |
| 141 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven Wire Micronic Filtering Mesh; ASTM E2016 stainless steel (grade 304) roll; Mesh Openings Range from 4 to 800 per inch; Mesh Diameter ranges from .0016" to 0.10"; Dimension ranges from 36"-48" wide by 100' long; Weave type: Plain Dutch Weave or Twill Dutch Weave; Mill finish |
| 142 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven Wire Micronic Filtering Mesh; ASTM E2016 stainless steel (grade 316) roll; Mesh Openings Range from 4 to 800 per inch; Mesh Diameter ranges from .0016" to 0.10"; Dimension ranges from 36"-48" wide by 100' long; Weave type: Plain Dutch Weave or Twill Dutch Weave; Mill finish |
| 143 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 Stainless Steel (grade 302) roll; 40 mesh wire openings per inch, 0.010" wire diameter, Dimensions: 4' wide by 100' long; Weave type: Plain Weave; Mill finish |
| 144 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 Stainless Steel (grade 304) roll; Opening Size ranges from 0.250"-4.000"; Wire diameter ranges from 0.063"-0.500"; Dimensions ranges from 36"-72" wide by 100' long; Weave type: Lockcrimp, Press-lock Crimp, Plain Weave; Mill finish |
| 145 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 Stainless Steel (grade 304) roll; Opening Size ranges from 2 to 370 mesh openings per inch; Wire diameter ranges from 0.0010" to 0.080"; Dimension ranges from 48"-60" wide by 100' long; Weave type: Press-lock Crimp, Intercrimp, Lockcrimp, Plain Crimp, Plain Weave, Twill Weave; Mill finish |
| 146 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 Stainless Steel (grade 304) roll; Opening Size ranges from 2 to 370 mesh openings per inch; Wire diameter ranges from 0.0010" to 0.080"; Dimension ranges from 60"-72" wide by 100' long; Weave type: Press-lock Crimp, Intercrimp, Lockcrimp, Plain Crimp, Plain Weave, Twill Weave; Mill finish |
| 147 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 Stainless Steel (grade 304) sheet; Opening Size ranges from 0.250"-2.000"; Wire diameter ranges from 0.063"-0.250"; Dimension: 48" wide by 96" long; Weave type: Plain Crimp, Lock Crimp, Inter Crimp, or Press-lock Crimp; Mill finish |
| 148 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 Stainless Steel (grade 316) roll; Opening Size ranges from 2 to 500 mesh openings per inch; Wire diameter ranges from 0.0009" to 0.063"; Dimension ranges from 36"-72" wide by 100' long; Weave type: Press-lock Crimp, Intercrimp, Lock Crimp, Plain Weave, Plain Crimp, or Twill Weave; Mill finish |
| 149 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 Stainless Steel (grade 316) sheet; Opening Size ranges from 0.375"-0.500"; Wire diameter: 0.125" thick; Dimension: 48" wide by 96" long; Weave type: Lock Crimp; Mill finish |
| 150 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 Stainless Steel (grade 316) sheet; Opening Size: 1.000"; Wire diameter ranges from 0.187"-0.250"; Dimension: 48" wide by 96" long; Weave type: Lock Crimp or Intercrimp; Mill finish |
| 151 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 Stainless Steel (grade 347) roll; 8 mesh wire openings per inch, 0.063" wire diameter, Dimensions: 4' wide by 100' long; Weave type: Plain Crimp; Mill finish |
| 152 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven stainless steel wire mesh for architectural applications: building facades, interior partitions, balustrade infill, ceiling panels |
| 153 | 7314.14.00 | Wire cloth, grill, netting and fencing | Woven stainless steel wire cloth for industrial screening, filtration, and sieving applications |
| 154 | 7314.19.00 | Wire cloth, grill, netting and fencing | Woven wire cloth of iron or non-alloy steel, produced from low-carbon steel wire, in plain or twill weave, in rolls, sheets, or slit strips, with a wire diameter of at least 0.20 mm but not exceeding 1.20 mm, with a mesh count of at least 4 but not exceeding 80 wires per inch, of a width of at least 609.6 mm but not exceeding 1,828.8 mm |
| 155 | 7314.19.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 AISI 1010 carbon bare steel roll; Opening size ranges from 0.250" - 1.000"; Wire diameter ranges from 0.125" - 0.162"; Dimensions range from 32"-72" wide by 75'-100' long; Weave type: Intercrimp & Lock Crimp; Mill finish |
| 156 | 7314.19.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 AISI 1010 carbon bare steel roll; Opening size ranges from 2 - 8 mesh openings per inch; Wire diameter ranges from 0.020" - 0.080"; Dimensions range from 36"-48" wide by 100'-200' long; Weave type: Lockcrimp, Plain Weave; Mill finish |
| 157 | 7314.19.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 AISI 1010 carbon bare steel sheet; Opening size ranges from 0.250" - 4.000"; Wire diameter ranges from 0.125" - 0.500"; Dimensions range from 48"-72" wide by 96"-144" long; Weave type: Plain Crimp, Intercrimp, Lock Crimp and Press-lock Crimp; Mill finish |
| 158 | 7314.19.00 | Wire cloth, grill, netting and fencing | Woven wire cloth of carbon or other steel (not stainless) for screening, filtration, and industrial separation |
| 159 | 7314.20.00 | Wire cloth, grill, netting and fencing | Low-carbon steel fence panels fabricated from steel tubes of specification ASTM A501 and welded wire mesh of specification ASTM A641, hot-rolled, with a wire diameter of 3.5 mm, with tube dimensions of 1 inch by 1 inch, with a wall thickness of 0.10 inches, with a panel width of 10 feet and with a panel height of 6 feet, powder coated |
| 160 | 7314.20.00 | Wire cloth, grill, netting and fencing | Low-carbon steel fence panels with integrated gate, fabricated from steel tubes of specification ASTM A501 and welded wire mesh of specification ASTM A641, hot-rolled, with a wire diameter of 3.5 mm, with tube dimensions of 1 inch by 1 inch, with a wall thickness of 0.10 inches, with a panel width of 10 feet, with a panel height of 6 feet, with a gate width of 40 inches and with a gate height of 6 feet, powder coated |
| 161 | 7314.31.00 | Wire cloth, grill, netting and fencing | Welded Wire galvanized (G90) ASTM A641 1010 carbon steel sheet; Opening size ranges from 1.000" - 4.000"; Wire diameter ranges from 0.063" - 0.250"; Dimensions range from 48"-72" wide by 96"-120" long; Hot dipped galvanized |
| 162 | 7314.31.00 | Wire cloth, grill, netting and fencing | Welded Wire ASTM A185 Mesh galvanized AISI 1010 carbon steel roll; ASTM A641 hot-dipped galvanized after; Opening size ranges from 1.000" - 2.000"; Wire diameter ranges from 0.063" - 0.135"; Dimensions range from 36"-60" wide by 100' long |
| 163 | 7314.31.00 | Wire cloth, grill, netting and fencing | Welded Wire Hardware Cloth ASTM A740 AISI 1008 galvanized carbon steel roll; Opening size ranges from 0.500"-1.000"; Wire diameter ranges from 0.032" - 0.080"; Dimensions ranges from 36"-72" wide by 100' long |
| 164 | 7314.31.00 | Wire cloth, grill, netting and fencing | Welded Wire Hardware Cloth ASTM A740 AISI 1008 galvanized carbon steel roll; Opening size ranges from 2-4 mesh openings per inch; Wire diameter ranges from 0.022" - 0.063"; Dimensions ranges from 36"-60" wide by 100' long |
| 165 | 7314.31.00 | Wire cloth, grill, netting and fencing | Cloth (including endless bands), grill, netting and fencing, of iron or steel wire; expanded metal of iron or steel. Other grill, netting and fencing, welded at the intersection. Plated or coated with zinc. Wire mesh used in the construction of lobster traps, zinc coated ASTM A641 with PVC coating ASTM D1499/G23. Wire Gauges including 10, 10.5, 12, 12.5, 14, 16. |
| 166 | 7314.31.00 | Wire cloth, grill, netting and fencing | Cloth (including endless bands), grill, netting and fencing, of iron or steel wire; expanded metal of iron or steel. Other grill, netting and fencing, welded at the intersection. Plated or coated with zinc. Brickless bottoms used in the construction of lobster traps. Zinc coated ASTM A641 with PVC coating ASTM D1499/G23. Wire Gauges including 8, 10, 10.5, 12, 12.5, 14, 16 |
| 167 | 7314.31.00 | Wire cloth, grill, netting and fencing | Prefabricated temporary construction fence panels with stands and clips, of low-carbon steel wire of specification ASTM A185, welded wire mesh of 50.8 mm by 101.6 mm, with a wire diameter of at least 4.12 mm but not exceeding 4.88 mm, with a rectangular steel tube frame of 25.4 mm by 50.8 mm, with panel dimensions of 1,829 mm in height and with a width of at least 2,438 mm but not exceeding 3,048 mm, with cast iron or carbon steel 4-prong base stands, with carbon steel clips, hot-dip galvanized to ASTM A123 or powder coated |
| 168 | 7314.31.00 | Wire cloth, grill, netting and fencing | Welded wire fencing, grill, and netting with zinc coating: farm fencing, property fencing, animal enclosures |
| 169 | 7314.31.00 | Wire cloth, grill, netting and fencing | Welded wire reinforcement (WWR) mesh with zinc coating for concrete reinforcing applications |
| 170 | 7314.31.00 | Wire cloth, grill, netting and fencing | Welded wire mesh with zinc coating and PVC coating (ASTM A641/D1499), for construction of lobster traps and marine fishing gear |
| 171 | 7314.31.00 | Wire cloth, grill, netting and fencing | Prefabricated temporary construction fence panels with stands and clips (ASTM A185 welded wire, steel tube frame), galvanized or powder coated |
| 172 | 7314.39.00 | Wire cloth, grill, netting and fencing | Welded Wire Mesh ASTM A185 AISI 1010 carbon bare steel (1010 alloy) roll; Opening size ranges from 0.500" - 6.000"; Wire diameter ranges from 0.063" - 0.187"; Dimensions range from 48"-72" wide by 100'-200' long |
| 173 | 7314.39.00 | Wire cloth, grill, netting and fencing | Welded Wire Mesh ASTM A580 stainless steel (grade 304) roll; Opening size ranges from 0.250" - 2.000"; Wire diameter ranges from 0.028" - 0.080"; Dimensions range from 36"-60" wide by 100' long; Mill finish |
| 174 | 7314.39.00 | Wire cloth, grill, netting and fencing | Welded Wire Mesh ASTM A580 stainless steel (grade 316) roll; Opening size ranges from 0.330" - 1.000"; Wire diameter of either 0.047" or 0.063"; Dimensions: 48" wide by 100' long |
| 175 | 7314.39.00 | Wire cloth, grill, netting and fencing | Welded Wire ASTM A580 stainless steel (grade 304) BBQ grill sheet; Opening size: 0.5"x3.00"; Wire diameter: 0.187"x0.250"; Dimensions: 48" wide by 96" long; mill finish |
| 176 | 7314.39.00 | Wire cloth, grill, netting and fencing | Welded Wire ASTM A580 stainless steel (grade 304) sheet; Opening size ranges from 0.750" - 2.000"; Wire diameter ranges from 0.105" - 0.250"; Dimensions range from 39"-60" wide by 43"-120" long; mill finish |
| 177 | 7314.39.00 | Wire cloth, grill, netting and fencing | Welded Wire ASTM A580 stainless steel (grade 304) sheet; Opening size ranges from 2.01" - 4.00"; Wire diameter ranges from 0.125" - 0.250"; Dimensions range from 48"-60" wide by 96"-120" long; mill finish |
| 178 | 7314.39.00 | Wire cloth, grill, netting and fencing | Welded Wire ASTM A580 stainless steel (grade 316) sheet; Opening size ranges from 1.000" - 2.000"; Wire diameter ranges from 0.120" - 0.250"; Dimensions: 48" wide by 96" long; mill finish |
| 179 | 7314.39.00 | Wire cloth, grill, netting and fencing | Welded Wire ASTM A185 AISI 1010 carbon steel BBQ grill sheet; Opening size: 0.5"x3.00"; Wire diameter: 0.187"x0.250"; Dimensions: 48" wide by 96" long; mill finish |
| 180 | 7314.39.00 | Wire cloth, grill, netting and fencing | Welded Wire ASTM A185 AISI 1010 carbon steel sheet; Opening size ranges from 0.750" - 3.000"; Wire diameter ranges from 0.120" - 0.375"; Dimensions range from 48"-72" wide by 96"-120" long |
| 181 | 7314.39.00 | Wire cloth, grill, netting and fencing | Welded Wire ASTM D1499 UV PVC coated AISI 1010 hot-dipped galvanized carbon steel roll; Opening size ranges from 0.5"-2"; Wire diameter ranges from 0.063" - 0.1"; Dimension: 48" wide by 100' long; black or yellow PVC coating; PVC thickness ranges from 0.02"-0.045" |
| 182 | 7314.39.00 | Wire cloth, grill, netting and fencing | Welded Wire ASTM D1499 UV PVC coated AISI 1010 hot-dipped galvanized carbon steel sheet; Opening size ranges from 0.5"-2"; Wire diameter ranges from 0.063" - 0.1"; Dimensions range from 48"-72" wide by 96"-120" long; black or yellow PVC coating; PVC thickness ranges from 0.02"-0.045" |
| 183 | 7314.39.00 | Wire cloth, grill, netting and fencing | Prefabricated temporary construction fence panels with stands and clips, of low-carbon steel wire of specification ASTM A185, welded wire mesh of 50.8 mm by 101.6 mm, with a wire diameter of at least 4.12 mm but not exceeding 4.88 mm, with a rectangular steel tube frame of 25.4 mm by 50.8 mm, with panel dimensions of 1,829 mm in height and with a width of at least 2,438 mm but not exceeding 3,048 mm, with cast iron or carbon steel 4-prong base stands, with carbon steel clips, hot-dip galvanized to ASTM A123 or powder coated |
| 184 | 7314.39.00 | Wire cloth, grill, netting and fencing | Welded wire industrial grating, grill, and netting: machine guards, safety barriers, ventilation screens |
| 185 | 7314.39.00 | Wire cloth, grill, netting and fencing | Welded wire reinforcement (WWR) mesh without zinc coating for concrete reinforcing and construction |
| 186 | 7314.41.00 | Wire cloth, grill, netting and fencing | Woven Wire Hardware Cloth ASTM A740 AISI 1008 galvanized carbon steel roll; Opening size ranges from 3-8 mesh openings per inch; Wire diameter ranges from 0.015" - 0.080"; Dimensions ranges from 36"-48" wide by 100' long; Weave type: Plain weave |
| 187 | 7314.41.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 AISI 1010 galvanized carbon steel roll; Opening size of either 0.50" or 0.865"; Wire diameter ranges from 0.125" - 0.135"; Dimensions: 48" wide by 100' long; G70 - G80 zinc coating; Weave Style: Lockcrimp |
| 188 | 7314.41.00 | Wire cloth, grill, netting and fencing | Woven Wire ASTM E2016 AISI 1010 hot-dipped galvanized carbon steel roll; Opening size ranges from 3-8 mesh openings per inch; Wire diameter ranges from 0.015" - 0.080"; Dimensions ranges from 36"-48" wide by 100' long; Weave type: Plain weave |
| 189 | 7314.41.00 | Wire cloth, grill, netting and fencing | Woven chain link wire mesh fencing; wire diameter: 9 ga (3.76 mm) and 11 ga (3.05 mm); mesh opening: 1.5" x 1.5" (38.1 x 38.1 mm) and 2" x 2" (50.8 x 50.8 mm); roll height: 4 ft (1,219 mm) and 6 ft (1,829 mm); material: carbon steel, Grade 1018 or equivalent; (a) Hot-dip galvanized (HDG) coating per ASTM A392, Class 2 zinc coating (minimum 1.2 oz/ft²); (b) Black PVC/polyester powder coat per ASTM F668, Class 2b (PVC-coated over galvanized wire), minimum 10 mil coating thickness. |
| 190 | 7314.41.00 | Wire cloth, grill, netting and fencing | Galvanized hardware cloth (welded or woven tight-mesh wire) for pest exclusion, garden protection, and general utility screening |
| 191 | 7314.41.00 | Wire cloth, grill, netting and fencing | Hexagonal wire netting (chicken wire) with zinc coating for poultry enclosures, garden fencing, and light animal containment |
| 192 | 7314.41.00 | Wire cloth, grill, netting and fencing | Woven (knotted or hinged-joint) field fencing with zinc coating for agricultural and rural property perimeter fencing |
| 193 | 7314.41.00 | Wire cloth, grill, netting and fencing | Woven chain-link wire mesh fencing (ASTM A392), carbon steel, hot-dip galvanized Class 2 or PVC/polyester powder coated |
| 194 | 7314.42.00 | Wire cloth, grill, netting and fencing | Steel wire mesh of grade 36 of specification EN 16120-2, galvanized before electro welding, with a thickness of 2.51 mm or 3.25 mm, with a width of at least 6 inches but not exceeding 66 inches and with a length of 100 feet, hot-dip galvanized after welding and PVC coated |
| 195 | 7314.42.00 | Wire cloth, grill, netting and fencing | Steel wire mesh of grade 36 of specification EN 16120-2, galvanized before electro welding, with a thickness of 1.29 mm, with a width of at least 6 inches but not exceeding 66 inches and with a length of 100 feet, hot-dip galvanized after welding and PVC coated |
| 196 | 7314.42.00 | Wire cloth, grill, netting and fencing | Steel wire mesh of grade 36 of specification EN 16120-2, galvanized before electro welding, with a thickness of 1.628 mm, with a width of at least 6 inches but not exceeding 66 inches and with a length of 100 feet, hot-dip galvanized after welding and PVC coated |
| 197 | 7314.42.00 | Wire cloth, grill, netting and fencing | PVC-coated galvanized carbon steel wire mesh for lobster traps, of specification ASTM A1064 and ASTM A641, with a wire diameter before coating of 0.099 inches (12.5 gauge) or 0.128 inches (10.5 gauge), PVC coated over zinc galvanization |
| 198 | 7314.42.00 | Wire cloth, grill, netting and fencing | PVC-coated chain-link fencing fabric for residential, commercial, and institutional perimeter fencing |
| 199 | 7314.42.00 | Wire cloth, grill, netting and fencing | Plastic-coated wire mesh for garden, landscape, and specialty applications (other than chain-link) |
| 200 | 7314.42.00 | Wire cloth, grill, netting and fencing | PVC-coated galvanized carbon steel wire mesh (ASTM A1064/A641), various wire gauges, for lobster trap construction |
| 201 | 7314.49.00 | Wire cloth, grill, netting and fencing | Non-welded wire cloth, grill, netting and fencing with other coatings or uncoated: stainless or specialty alloy mesh |
| 202 | 7314.50.00 | Wire cloth, grill, netting and fencing | ASTM F1267 expanded metal grating stainless steel (grade 304); Short opening dimension is 1.33"; Long opening dimension is 5.33"; Load rating: 3 lbs/square foot; Dimensions: 48" wide by 96" long; 300 min. lbs |
| 203 | 7314.50.00 | Wire cloth, grill, netting and fencing | ASTM F1267 expanded metal grating, AISI 1008 bare carbon steel; Short opening dimension is 1.33"; Long opening dimension is 5.33"; Load rating: ranges from 3-7 lbs/square foot; Dimensions range from 48" wide by 96"-120" long; Mill finish |
| 204 | 7314.50.00 | Wire cloth, grill, netting and fencing | ASTM F1267 expanded metal sheets, AISI 1008 bare carbon steel; ASTM A123 hot-dipped galvanizing finish; Short opening dimension ranges from 0.187" to 1.500"; Long opening dimension ranges from 0.500" to 3.000"; metal thickness ranging from 0.026"-0.188"; Flat or raised style; Dimensions range from 43"-60" wide and 92"-120" long |
| 205 | 7314.50.00 | Wire cloth, grill, netting and fencing | ASTM F1267 expanded metal sheets, stainless steel (grade 304); Short opening dimension ranges from 0.187" to 1.500"; Long opening dimension ranges from 0.500" to 3.000"; metal thickness ranging from 0.026"-0.140"; Flat or raised style; Dimensions: 48" wide by 96" long |
| 206 | 7314.50.00 | Wire cloth, grill, netting and fencing | ASTM F1267 expanded metal sheets, stainless steel (grade 316); Short opening dimension ranges from 0.187" to 1.500"; Long opening dimension ranges from 0.500" to 3.000"; metal thickness ranging from 0.026"-0.140"; Flat or raised style; Dimensions: 48" wide by 96" long |
| 207 | 7314.50.00 | Wire cloth, grill, netting and fencing | Expanded metal for architectural applications: building facades, sunscreens, decorative panels, ceiling systems |
| 208 | 7314.50.00 | Wire cloth, grill, netting and fencing | Expanded metal for industrial applications: walkway grating, machine guards, screening panels, safety barriers, filtration media |
| 209 | 7315.11.00 | Chains and parts | Roller chain of carbon, alloy or stainless steel, of specification ANSI/ASME B29.1, including simplex roller chains, heavy roller chains, duplex chains, double pitch drive chains, double pitch conveyor chains and agricultural CA-type chains, with a pitch of at least 6 mm but not exceeding 101.6 mm, with a link plate height of at least 6 mm but not exceeding 47.8 mm and with a pin diameter of at least 2.31 mm but not exceeding 19.85 mm, uncoated, dacromet plated or nickel plated |
| 210 | 7315.11.00 | Chains and parts | Roller chain coils of grade 4140 of specification ANSI B29.1, cold-rolled, with a length of at least 27 inches but not exceeding 27.04 inches, oiled |
| 211 | 7315.11.00 | Chains and parts | Roller chain connecting links of grade 4140 of specification ANSI B29.1, cold-rolled, with a length of at least 27 inches but not exceeding 27.04 inches, oiled |
| 212 | 7315.11.00 | Chains and parts | Roller chain coils of grade 4140 of specification ANSI B29.1, cold-rolled, with a length of at least 27 inches but not exceeding 27.04 inches, nickel plated |
| 213 | 7315.11.00 | Chains and parts | Roller chain of carbon steel, alloy steel or stainless steel of specification ANSI B29.1, ISO 606B, BS 228 or DIN 8187, assembled, with an inner link width of at least 0.125 inches but not exceeding 1.875 inches, with a roller diameter of at least 0.13 inches but not exceeding 2.25 inches and with a pitch of at least 0.25 inches but not exceeding 4 inches, rustproofed, nickel plated, zinc plated and/or treated |
| 214 | 7315.11.00 | Chains and parts | Roller chain ANSI 2080 pitch 2'' 1 row heavy duty -10 ' in stainless steel |
| 215 | 7315.11.00 | Chains and parts | Roller chain ANSI 2160 pitch 2'' 1 row heavy duty -10 ' length with attachment |
| 216 | 7315.11.00 | Chains and parts | Roller chain ANSI 40 pitch 1/2'' 1 row with 25 links without connecting link |
| 217 | 7315.11.00 | Chains and parts | Roller chain ANSI 41 pitch 1/2'' 1 row with 44 links including 1 junction link |
| 218 | 7315.11.00 | Chains and parts | Roller chain ANSI 41 pitch 1/2'' 1 row with 46 links including 1 junction link |
| 219 | 7315.11.00 | Chains and parts | Roller chain ANSI 41 pitch 1/2'' 1 row with 48 links endless riveted |
| 220 | 7315.11.00 | Chains and parts | Roller chain ANSI 41 pitch 1/2'' 1 row with 72 links including 1 junction link |
| 221 | 7315.11.00 | Chains and parts | Roller chain ANSI 41 pitch 1/2'' 1 row with 78 links including 1 junction link |
| 222 | 7315.11.00 | Chains and parts | Roller chain ANSI 41 pitch 1/2'' 1 row with 96 links including 1 junction link |
| 223 | 7315.11.00 | Chains and parts | Roller chain ANSI 410 pitch 1/2'' 1 row with 48 links endless riveted |
| 224 | 7315.11.00 | Chains and parts | Single-strand roller chain of carbon steel and alloy steel of grade SAE 1010, SAE 1040 and SAE 4119, with a pitch of 0.5 inches ANSI #40 or 41 , with a connecting link, uncoated |
| 225 | 7315.11.00 | Chains and parts | Roller chain ANSI 50 pitch 5/8'' 1 row with 100 links |
| 226 | 7315.11.00 | Chains and parts | Roller chain ANSI 50 pitch 5/8'' 1 row with 76 links including 1 junction link |
| 227 | 7315.11.00 | Chains and parts | Roller chain ANSI 50 pitch 5/8'' 1 row with 96 links including 1 junction link |
| 228 | 7315.11.00 | Chains and parts | Roller chain ANSI 81x pitch 1/2'' 1 row - 10' length with attachment |
| 229 | 7315.11.00 | Chains and parts | Power transmission roller chain (e.g., ANSI standard 25-240 series) for conveyors, agricultural equipment, motorcycles, industrial drives, material handling |
| 230 | 7315.12.00 | Chains and parts | Leaf chain of carbon, alloy or stainless steel, of specification ANSI B29.8, of balanced or unbalanced construction, uncoated, dacromet plated or nickel plated |
| 231 | 7315.12.00 | Chains and parts | Steel bicycle chains of bushing-type (non-roller) design, of standard ISO 606, with a pitch of 12.7 mm, with an inner width of at least 2.18 mm but not exceeding 3.175 mm, for single-speed through 12-speed drivetrains |
| 232 | 7315.12.00 | Chains and parts | Chain of carbon steel, alloy steel or stainless steel of specification ISO 4948, ANSI B29.22.2001, ANSI B29.15M 1997 or ANSI B29.10M 1997, assembled, with an inner link width of at least 1 inch but not exceeding 11 inches, with a roller diameter of at least 0.906 inches but not exceeding 4.5 inches and with a pitch of at least 1.75 inches but not exceeding 18 inches, rustproofed, nickel plated, zinc plated and/or Neptune treated |
| 233 | 7315.12.00 | Chains and parts | Pintle chain ANSI 667 - 112 pitch with flat bar 16.000 center to center 3/8'' thickness / 1'' high |
| 234 | 7315.12.00 | Chains and parts | Pintle chain ANSI 667 - 155 pitch with flat bar 16.000 center to center 3/8'' thickness / 1'' high |
| 235 | 7315.12.00 | Chains and parts | Pintle chain ANSI 88K - 119 pitch with flight bars on 22.000 centre to center 3/8'' thickness - 1 1/4'' high |
| 236 | 7315.12.00 | Chains and parts | Pintle chain of specification ANSI 88K 2.609 in pitch with 138 links with flat bar, with a center-to-center distance of 24.739 in, a thickness of 0.5 in and a height of 1.25 in |
| 237 | 7315.12.00 | Chains and parts | Special chain ANSI C55 - 1.631'' pitch with 1 row 50' length heavy duty |
| 238 | 7315.12.00 | Chains and parts | Special welded steel chain ANSI 82 - 40 pitch attachment A22 with alternated attach on 20 pitch no standard with bushed feet with thermical treatment |
| 239 | 7315.12.00 | Chains and parts | Other articulated link chain (non-roller): silent chain, leaf chain, engineered-class chain for industrial and agricultural applications |
| 240 | 7315.12.00 | Chains and parts | Pintle chain of carbon steel (ANSI 667, 88K, C55 series), with flight bars and attachments, for conveyor and agricultural equipment |
| 241 | 7315.12.00 | Chains and parts | Steel bicycle chains of bushing-type (non-roller) design, ISO 606, 12.7mm pitch, for single through 12-speed drivetrains |
| 242 | 7315.19.00 | Chains and parts | Connecting links, offset links and repair links of carbon, alloy or stainless steel, for use with roller chain and leaf chain, including spring clip, cottered, press-fit, single offset and double offset types, coated or uncoated |
| 243 | 7315.19.00 | Chains and parts | Parts for roller chain of carbon steel, alloy steel or stainless steel of specification ANSI B29.1, ISO 606B, BS 228 or DIN 8187, assembled, with an inner link width of at least 0.125 inches but not exceeding 1.875 inches, with a roller diameter of at least 0.130 inches but not exceeding 2.25 inches and with a pitch of at least 0.25 inches but not exceeding 4.0 inches, rustproofed, nickel plated, zinc plated and/or Neptune treated |
| 244 | 7315.19.00 | Chains and parts | Parts for chain of carbon steel, alloy steel or stainless steel of specification ISO 4948, ANSI B29.22.2001, ANSI B29.15M 1997 or ANSI B29.10M 1997, assembled, with an inner link width of at least 1 inch but not exceeding 11 inches, with a roller diameter of at least 0.906 inches but not exceeding 4.5 inches and with a pitch of at least 1.75 inches but not exceeding 18 inches, rustproofed, nickel plated, zinc plated and/or Neptune treated |
| 245 | 7315.19.00 | Chains and parts | Replacement parts for articulated link chain: connecting links, offset links, attachment links, pins, bushings, rollers, side plates |
| 246 | 7315.19.00 | Chains and parts | Low carbon steel or alloy steel tire chain parts, including cross chains pre-assembled with hooks, loose cross chain hooks (standard and bell-shaped), side chain end hooks, side chain fasteners, and side chains with cam tightening devices, with a wire or material diameter of at least 4.5 mm but not exceeding 13 mm, clear lacquer coated |
| 247 | 7315.20.00 | Chains and parts | Tire chains (skid chain) for motor vehicles, trucks, and heavy equipment: winter traction, forestry, and mining applications |
| 248 | 7315.20.00 | Chains and parts | Low carbon steel or alloy steel complete tire chains for on-highway vehicles, including cable or wire anti-skid devices, hoop-style chains, studded chains, V-bar chains, square link chains, and regular twist link chains, in single or triple configurations, with or without cam side chain tightening devices, with a wire or link diameter of at least 3.8 mm but not exceeding 17.3 mm, clear lacquer, zinc plated, bright zinc or PVC coated, for use on passenger vehicles, light trucks, SUVs, medium trucks, heavy trucks, and ATVs/UTVs |
| 249 | 7315.20.00 | Chains and parts | Low carbon steel or alloy steel complete tire chains for off-highway equipment, including studded diamond pattern, H-pattern, square link, net link, multi-ring, and U-grip configurations, with a wire or link diameter of at least 7 mm but not exceeding 32 mm, clear lacquer or grey paint coated, for use on agricultural, industrial, loader/grader, forklift, and forestry equipment |
| 250 | 7315.81.00 | Chains and parts | Stud link anchor chain manufactured in accordance with ISO 1704 in Grades U2, U3 or U4, of carbon steel, with a diameter of at least 0.625 inches but not exceeding 2.500 inches and a length of 90 ft, galvanized or painted |
| 251 | 7315.81.00 | Chains and parts | Stud-link anchor chains of low-alloy steel of grade CM490 Grade 2, of specification ISO 1704 and GB/T 549-2017, welded, with a link diameter of 38 mm, with a link length of 228 mm, with an inside link opening of 152 mm long and 61 mm wide, with an overall chain length of 27.5 m, black oxide finish |
| 252 | 7315.81.00 | Chains and parts | Chain and parts thereof, of iron or steel. Stud-link Chain. Sizes from 1mm metric or 1/32" imperial and up. ISO 1704, Grade 2 and 3. Mooring/anchor chain |
| 253 | 7315.81.00 | Chains and parts | Stud-link anchor chain for marine, mooring, and offshore applications (typically to classification society standards) |
| 254 | 7315.82.00 | Chains and parts | Long link Studless mooring chain of grade manufactured to the steel standards of ISO 1704 for Grades U2, U3 or U4, of carbon steel, with a diameter of at least 0.375 inches but not exceeding 2.500 inches and a length of 90 ft or 100 ft, galvanized or painted |
| 255 | 7315.82.00.10 | Chains and parts | Chaîne de convoyeur à maillons soudés en acier au carbone de dimension nominale de 5/8 de pouce, de type ANSI CNX, avec 2 traverses et attaches de convoyeur, d'un pas de 203 mailles, brute ou huilée |
| 256 | 7315.82.00.10 | Chains and parts | Chaîne de convoyeur à maillons soudés en acier au carbone de dimension nominale de 5/8 de pouce, de type CNX, de conception à ouverture libre (break open), d'un pas de 254 mailles, brute ou huilée |
| 257 | 7315.82.00.10 | Chains and parts | Chaîne de sécurité à maillons soudés en acier au carbone de dimension nominale de 5/16 de pouce, d'une longueur de 40 pouces, avec attache à manille (clevis), galvanisée |
| 258 | 7315.82.00.10 | Chains and parts | Chaîne de convoyeur à maillons soudés en acier au carbone de dimension nominale de 5/8 de pouce, de type CNX, à 2 brins avec attaches de convoyeur, d'un pas de 179 mailles, brute ou huilée |
| 259 | 7315.82.00.10 | Chains and parts | Chain and parts thereof, of iron or steel. Other, welded link. Of iron or non-alloy steel. Sizes from 1mm metric or 1/32" imperial and up. Grades including G20, G30, G40, G43, G50, G63, etc. Link Types including Regular, short, mid, long, cross, side, studded cross, V-bar cross, super sweep, open link, etc. Finishes including Galvanized, Self Coloured, Zinc Plated, Painted, Powder Coated, etc. To NACM standards |
| 260 | 7315.82.00.10 | Chains and parts | Welded-link chain of carbon or non-alloy steel: proof coil chain, high-test chain for general lifting, towing, logging, securing loads |
| 261 | 7315.82.00.10 | Chains and parts | Welded-link conveyor chain of carbon steel (CNX type), with traverses and attachments, for industrial conveyor and material handling |
| 262 | 7315.82.00.10 | Chains and parts | Welded-link safety chain of carbon steel, short lengths with clevis or other attachment, for securing trailers, equipment, and loads |
| 263 | 7315.82.00.10 | Chains and parts | Low carbon steel welded link chain in regular twist link pattern, to NACM tire chain specifications, with a wire diameter of at least 7 mm but not exceeding 10 mm, clear lacquer coated, for use as tire chain cross chains or side chains |
| 264 | 7315.82.00.20 | Chains and parts | Stainless steel chains of grade 316L, of specification MIL-DTL-32655, calibrated, with a diameter of 0.19 inches, an inner length of 0.58 inches and an inner width of 0.25 inches, rated as Grade 50 with a working load limit of 1,100 lbs, a minimum breaking strength of 4,400 lbs, spheroidized annealed, uncoated |
| 265 | 7315.82.00.20 | Chains and parts | Stainless steel chains of grade 316L, of specification MIL-DTL-32655, calibrated, with a diameter of 0.28 inches, an inner length of 0.85 inches and an inner width of 0.38 inches, rated as Grade 50 with a working load limit of 2,200 lbs, a minimum breaking strength of 8,800 lbs, spheroidized annealed, uncoated |
| 266 | 7315.82.00.20 | Chains and parts | Stainless steel chains of grade 316L, of specification MIL-DTL-32655, calibrated, with a diameter of 0.39 inches, an inner length of 1.18 inches and an inner width of 0.55 inches, rated as Grade 50 with a working load limit of 4,400 lbs, a minimum breaking strength of 17,600 lbs, spheroidized annealed, uncoated |
| 267 | 7315.82.00.20 | Chains and parts | Stainless steel chains of grade 316L, of specification MIL-DTL-32655, calibrated, with a diameter of 0.51 inches, an inner length of 1.55 inches and an inner width of 0.75 inches, rated as Grade 50 with a working load limit of 7,300 lbs, a minimum breaking strength of 29,200 lbs, spheroidized annealed, uncoated |
| 268 | 7315.82.00.20 | Chains and parts | Stainless steel chains of grade 316L, of specification MIL-DTL-32655, calibrated, with a diameter of 0.63 inches, an inner length of 1.91 inches and an inner width of 0.90 inches, rated as Grade 50 with a working load limit of 9,800 lbs, a minimum breaking strength of 39,200 lbs, spheroidized annealed, uncoated |
| 269 | 7315.82.00.20 | Chains and parts | Stainless steel chains of grade 316L, of specification MIL-DTL-32655, calibrated, with a diameter of 0.32 inches, an inner length of 0.95 inches and an inner width of 0.45 inches, rated as Grade 50 with a working load limit of 2,700 lbs, a minimum breaking strength of 10,800 lbs, spheroidized annealed, uncoated |
| 270 | 7315.82.00.20 | Chains and parts | Alloy steel chains of grade 80, of specification EN 818, heat treated, quenched and tempered, spheroidized annealed, with a diameter of 0.75 inches, a length of 7 feet, link dimensions of 4.5 inches by 3 inches, ring diameter of 1 inch with a width of 8 inches across, toggle length of 12 inches and plate thickness of 0.75 inches, uncoated |
| 271 | 7315.82.00.20 | Chains and parts | Alloy steel chains of grade 80, of specification EN 818, heat treated, quenched and tempered, spheroidized annealed, with a chain diameter of 0.75 inches, a chain length of 7 feet, a ring diameter of 1 inch, a toggle length of 12 inches, link dimensions of 4.5 inches by 3 inches, a ring width of 8 inches across and a plate thickness of 0.75 inches, uncoated |
| 272 | 7315.82.00.20 | Chains and parts | Alloy steel chains of grade 80, of specification EN 818, heat treated, quenched and tempered, spheroidized annealed, with a chain diameter of 0.75 inches, an overall length of 9 feet, a ring diameter of 1 inch, a toggle length of 12 inches, link dimensions of 6.5 inches by 3.5 inches, a ring width of 10 inches across and a plate thickness of 0.75 inches, uncoated |
| 273 | 7315.82.00.20 | Chains and parts | Alloy steel chains of grade 80, of specification EN 818, heat treated, quenched and tempered, spheroidized annealed, with a chain diameter of 1 inch, an overall length of 7 feet, a ring diameter of 1 inch, a toggle length of 12 inches, link dimensions of 6.5 inches by 3.5 inches, a ring width of 10 inches across and a plate thickness of 0.75 inches, uncoated |
| 274 | 7315.82.00.20 | Chains and parts | Alloy steel chains of grade 80, of specification EN 818, heat treated, quenched and tempered, spheroidized annealed, with a chain diameter of 0.75 inches, a length of 100 feet, link dimensions of 6.5 inches by 3 inches and a ring diameter of 1 inch with a width of 8 inches across, galvanized |
| 275 | 7315.82.00.20 | Chains and parts | Chaînes de convoyeur à maillons soudés en acier de grade 80, de dimension nominale de 5/8 de pouce, avec ou sans traverses et attaches de convoyeur, de type standard ou à ouverture libre (break open), d'un pas d'au moins 203 mm mais n'excédant pas 254 mm |
| 276 | 7315.82.00.20 | Chains and parts | Open link (studless) anchor chains of low-alloy steel of grade CM490 Grade 2, of specification ISO 1704 and GB/T 549-2017, welded, with a link diameter of at least 28 mm but not exceeding 38 mm, with a link length of at least 168 mm but not exceeding 228 mm, with an inside link opening of at least 112 mm but not exceeding 152 mm long and at least 42 mm but not exceeding 60.8 mm wide, with an overall chain length of at least 1.14 m but not exceeding 27.5 m, black oxide finish |
| 277 | 7315.82.00.20 | Chains and parts | Chain and parts thereof, of iron or steel. Other, welded link. Of alloy steel. Sizes from 1mm metric or 1/32" imperial and up. Grades including G70, G80, G90, G95, G100, G120, Hardened, etc,. Link Types including Regular, short, mid, long, cross, side, studded cross, V-bar cross, super sweep, open link, etc. Finishes including Galvanized, Self Coloured, Zinc Plated, Painted, Powder Coated, etc. To NACM standards |
| 278 | 7315.82.00.20 | Chains and parts | Welded-link chain of alloy steel for overhead lifting and rigging: Grade 80 and Grade 100 chain per ASTM A391/NACM standards |
| 279 | 7315.82.00.20 | Chains and parts | Open link (studless) mooring chain of alloy steel (Grade U2/U3/U4, ISO 1704), for marine mooring and offshore applications |
| 280 | 7315.82.00.20 | Chains and parts | Alloy steel chain sling assemblies (Grade 80, EN 818), with rings, toggles, and end fittings, for overhead lifting and rigging |
| 281 | 7315.82.00.20 | Chains and parts | Stainless steel calibrated chain (grade 316L), MIL-DTL-32655 Grade 50, for marine, defense, and corrosion-resistant applications |
| 282 | 7315.82.00.20 | Chains and parts | Alloy steel welded link chain in square link pattern, with a wire diameter of at least 6 mm but not exceeding 11 mm, clear lacquer coated, for use as tire chain cross chains or side chains |
| 283 | 7315.89.00 | Chains and parts | Alloy steel chain links of grade AISI 115MA or 105MA, or carbon steel chain links of specification ASTM A304, produced by investment casting (lost wax process), non-welded, as-cast or heat treated, of oval or round configuration, with a cross-sectional diameter of at least 16 mm but not exceeding 65 mm and with a length of at least 100 mm but not exceeding 400 mm |
| 284 | 7315.89.00 | Chains and parts | Chaîne de châssis (sash chain) en acier au carbone, taille 8, d'une largeur de 0,245 pouce, en rouleaux de 500 pieds, zinguée |
| 285 | 7315.89.00 | Chains and parts | Chaînes non soudées en acier au carbone de nuance SAE 1008, d'une longueur de maillon de 19 mm, d'un diamètre de fil de 4,5 mm ou 5 mm, d'une charge nominale d'au moins 30,7 tonnes mais n'excédant pas 31,4 tonnes, d'une longueur d'au moins 20 pieds mais n'excédant pas 1 000 pieds, zinguées |
| 286 | 7315.89.00 | Chains and parts | Carbon steel welded oval-link chain for gate closure, with a link wire diameter of 6 mm, with a chain length of at least 300 mm but not exceeding 500 mm, with connecting pin and mounting hardware, hot-dip galvanized to ASTM A153 Class C |
| 287 | 7315.89.00 | Chains and parts | Decorative and specialty chain: sash chain, jack chain, bead chain, safety chain, barrier chain |
| 288 | 7315.89.00 | Chains and parts | Alloy or carbon steel chain links produced by investment casting (lost wax process), for specialized marine, mining, and heavy-duty applications |
| 289 | 7315.90.00 | Chains and parts | Carbon steel or austenitic stainless steel connectors, shackles and joining components, for use as parts of chain, produced by investment casting (lost wax process), as-cast or machined, with a cross-sectional diameter of at least 20 mm but not exceeding 75 mm, with a width of at least 75 mm but not exceeding 300 mm and with a length of at least 100 mm but not exceeding 350 mm, uncoated |
| 290 | 7315.90.00 | Chains and parts | Anchor chain swivels manufactured under IACS requirements for use with Grade U3 anchor chain manufactured in accordance with ISO 1704, of carbon steel, with a diameter of at least 28 mm but not exceeding 75 mm, painted |
| 291 | 7315.90.00 | Chains and parts | Chain and parts thereof, of iron or steel. Other. Chain links/connecting links various sizes. Connecting links/hammerlocks G80/G100. Painted, galvanized or self coloured. To ASME B30.9 standard |
| 292 | 7315.90.00 | Chains and parts | Chain and parts thereof, of iron or steel. Other. Chain links/connecting links various sizes. Masterlinks G80/G100. Painted, galvanized or self coloured. To ASME B30.9 standard |
| 293 | 7315.90.00 | Chains and parts | Chain fittings for rigging and lifting: hooks, shackles, swivels, and rings |
| 294 | 7315.90.00 | Chains and parts | Light chain hardware: quick links, chain tensioners, end fittings, S-hooks, and lap links |
| 295 | 7315.90.00 | Chains and parts | Anchor chain swivels (IACS, ISO 1704 Grade U3), for connecting anchor chain to vessel mooring systems |
| 296 | 7315.90.00 | Chains and parts | Steel masterlinks and hammerlocks (connecting links), G80/G100, for chain sling assembly and overhead lifting connections |
| 297 | 7317.00.00 | Nails, tacks and staples | Carbon steel horseshoe nails of grade AISI 1008 to AISI 1010, of specification ASTM A1064, cold-rolled, with a length of at least 41 mm but not exceeding 77 mm, zinc electroplated to ASTM B633 or ASTM F1941, or copper coated to ASTM B734 |
| 298 | 7317.00.00 | Nails, tacks and staples | Stainless steel spikes of grade 304 of specification ASTM A240/A240M and ASTM A276, CNC machined, with a diameter of 7 mm, with a base width of 43 mm, with a base length of 83 mm, with a hole dimension of 30 mm by 33 mm and with a length of 11.5 inches, 13 inches or 14.5 inches, polyethylene powder coated |
| 299 | 7317.00.00 | Nails, tacks and staples | Fibres d’acier regroupées en bandes au moyen d’un liant hydrosoluble, de spécification ASTM A820, EN 14889-1 et ISO 13270 classe A, ayant des dimensions transversales d’au moins 0,75 mm mais n’excédant pas 0,90 mm, une résistance nominale à la traction de 2 200 MPa, un module de Young de 210 000 MPa, un allongement à la rupture de 0,8 % et un réseau de 4 644 fibres/kg, finition brillante |
| 300 | 7317.00.00 | Nails, tacks and staples | Carbon steel 15-degree wire-weld coil nails (smooth, ring, or spiral shank), ASTM F1667, for pneumatic coil nailers in construction framing and assembly |
| 301 | 7317.00.00 | Nails, tacks and staples | Carbon steel collated strip nails (plastic, paper tape, or wire collated), full round head or clipped head, ASTM F1667, for pneumatic framing nailers |
| 302 | 7317.00.00 | Nails, tacks and staples | Carbon steel bulk common nails and box nails (smooth shank, flat head), all standard penny sizes, ASTM F1667 |
| 303 | 7317.00.00 | Nails, tacks and staples | Hardened carbon steel concrete nails (fluted shank, countersunk head), 1045 steel case-hardened, for fastening to concrete and masonry |
| 304 | 7317.00.00 | Nails, tacks and staples | Carbon or stainless steel 15-degree coil roofing nails (smooth or ring shank, round head), galvanized, ASTM F1667 |
| 305 | 7317.00.00 | Nails, tacks and staples | Carbon or stainless steel bulk roofing nails (smooth or ring shank, round head), galvanized, ASTM F1667 |
| 306 | 7317.00.00 | Nails, tacks and staples | Carbon or stainless steel brad and finish nails (16, 18, 23 gauge), straight glue-collated strips, for pneumatic brad/pin nailers, trim and cabinetry |
| 307 | 7317.00.00 | Nails, tacks and staples | Carbon steel machine-quality bulk nails (spiral shank), for automatic nailing machines in pallet manufacturing and industrial packaging |
| 308 | 7317.00.00 | Nails, tacks and staples | Carbon steel ring-shank siding/drywall nails and double-headed (duplex) nails for temporary construction forming and scaffolding |
| 309 | 7317.00.00 | Nails, tacks and staples | Carbon steel metal-cap nails (spiral or ring shank), electro-galvanized, for house wrap, roofing underlayment, and insulation attachment |
| 310 | 7317.00.00 | Nails, tacks and staples | Carbon steel construction staples (7/16 crown, 1 crown, 1/4 narrow crown), 16 or 18 gauge, galvanized, for pneumatic staplers |
| 311 | 7317.00.00 | Nails, tacks and staples | Carbon steel horseshoe nails (AISI 1008-1010, ASTM A1064), cold-rolled, zinc or copper coated, for farrier and equine applications |
| 312 | 7317.00.00 | Nails, tacks and staples | Steel fibers (hooked-end, crimped, or micro), ASTM A820/EN 14889-1, for concrete reinforcement in industrial floors, tunnels, and precast elements |
| 313 | 7317.00.00 | Nails, tacks and staples | Stainless steel anti-climb/anti-perch spikes (grade 304), CNC machined, polyethylene powder coated, for building and infrastructure security |
| 314 | 7317.00.00 | Nails, tacks and staples | Carbon steel or stainless steel 15-degree wire-weld coil nails, smooth, spiral, ring or twisted screw shank, checkered round head or square drive, of grade Q235, C1018, C1022, C1042 or C1045, of specification ASTM F1667, with a shank diameter of at least 0.080 inches but not exceeding 0.148 inches, with a length of at least 1 inch but not exceeding 4 inches, brite, electro galvanized, hot-dip galvanized, resin coated, phosphate coated or 304 stainless steel |
| 315 | 7317.00.00 | Nails, tacks and staples | Carbon steel or stainless steel 15-degree wire-weld coil roofing nails, smooth or ring shank, round head, of grade Q235 or 304 stainless steel, of specification ASTM F1667, with a shank diameter of 0.12 inches, with a length of at least 0.75 inches but not exceeding 2 inches, electro galvanized, hot-dip galvanized or 304 stainless steel |
| 316 | 7317.00.00 | Nails, tacks and staples | Carbon steel 21-degree plastic collated strip nails, smooth or spiral shank, full round head or double head, of grade Q235, of specification ASTM F1667, with a shank diameter of at least 0.113 inches but not exceeding 0.148 inches, with a length of at least 2.375 inches but not exceeding 5.125 inches, brite basic coating |
| 317 | 7317.00.00 | Nails, tacks and staples | Carbon steel or high-carbon steel 28-degree, 30-degree or 34-degree paper tape collated or wire collated strip nails, smooth, spiral or ring shank, clip head, full round head or offset full round head, of grade Q235 or C1045, of specification ASTM F1667, with a shank diameter of at least 0.113 inches but not exceeding 0.148 inches, with a length of at least 1.5 inches but not exceeding 4 inches, brite, hot-dip galvanized or high-carbon coated |
| 318 | 7317.00.00 | Nails, tacks and staples | Carbon steel bulk common nails, smooth shank, flat head, diamond point, of grade 1018, C1022, C1042 or Q235, of specification ASTM F1667, with a shank diameter of at least 0.072 inches but not exceeding 0.192 inches, with a length of at least 1 inch but not exceeding 8 inches, brite, hot-dip galvanized, phosphate coated or vinyl coated |
| 319 | 7317.00.00 | Nails, tacks and staples | Carbon steel bulk box nails, smooth shank, flat head, diamond point, of grade 1018, of specification ASTM F1667, with a shank diameter of at least 0.076 inches but not exceeding 0.148 inches, with a length of at least 1.25 inches but not exceeding 4 inches, phosphate coated or vinyl coated |
| 320 | 7317.00.00 | Nails, tacks and staples | Hardened carbon steel bulk concrete nails, fluted shank, countersunk head, diamond point, of grade C1045 or C1022, of specification ASTM F1667, with a shank diameter of 0.148 inches, with a length of at least 1 inch but not exceeding 3 inches, brite basic coating |
| 321 | 7317.00.00 | Nails, tacks and staples | Carbon steel bulk double-headed nails, smooth shank, double head, diamond point, of grade 1006 or C1022, of specification ASTM F1667, with a shank diameter of at least 0.113 inches but not exceeding 0.191 inches, with a length of at least 1.75 inches but not exceeding 3.5 inches, brite basic coating |
| 322 | 7317.00.00 | Nails, tacks and staples | Carbon steel bulk drywall nails, ring shank, flat head, diamond point, of grade 1018 or C1022, of specification ASTM F1667, with a shank diameter of 0.099 inches, with a length of at least 1.25 inches but not exceeding 2 inches, brite basic coating |
| 323 | 7317.00.00 | Nails, tacks and staples | Carbon steel bulk lining nails, smooth shank, flat head, diamond point, of grade 1018 or C1022, of specification ASTM F1667, with a shank diameter of at least 0.080 inches but not exceeding 0.099 inches, with a length of at least 1.25 inches but not exceeding 2 inches, brite basic coating |
| 324 | 7317.00.00 | Nails, tacks and staples | Carbon steel bulk metal connector nails, spiral or ring shank, round metal cap head, diamond point, of grade 1018, of specification ASTM F1667, with a shank diameter of at least 0.11 inches but not exceeding 0.148 inches, with a length of at least 1 inch but not exceeding 5 inches, electro galvanized |
| 325 | 7317.00.00 | Nails, tacks and staples | Carbon steel bulk plastic cap nails with 1-inch plastic cap, spiral or ring shank, diamond point, of grade 1006 or C1022, of specification ASTM F1667, with a shank diameter of 0.083 inches, with a length of at least 1.25 inches but not exceeding 3 inches, electro galvanized |
| 326 | 7317.00.00 | Nails, tacks and staples | Carbon steel bulk siding and sheathing nails, spiral shank, flat head, diamond point, of grade 1018, C1022 or Q235, of specification ASTM F1667, with a shank diameter of at least 0.080 inches but not exceeding 0.138 inches, with a length of at least 1.25 inches but not exceeding 3.25 inches, brite, hot-dip galvanized or spiral shank screw type |
| 327 | 7317.00.00 | Nails, tacks and staples | Carbon steel or stainless steel machine-quality bulk nails, spiral or ring shank, flat head, blunt diamond point or clinch point, of grade 1010, 1018, 1042 or 304 stainless steel, of specification ASTM F1667, with a shank diameter of at least 0.086 inches but not exceeding 0.135 inches, with a length of at least 1.5 inches but not exceeding 3.5 inches, brite or electro galvanized, for use in automatic nailing machines |
| 328 | 7317.00.00 | Nails, tacks and staples | Carbon steel or stainless steel straight glue-collated strip nails, smooth shank, 16 gauge T head (0.063 inch), 18 gauge medium head (0.049 inch) or 23 gauge headless (0.026 inch), chisel point or diamond point, of grade Q235 or 304 stainless steel, of specification ASTM F1667, with a length of at least 0.5 inches but not exceeding 2.5 inches, electro galvanized or 304 stainless steel |
| 329 | 7317.00.00 | Nails, tacks and staples | Carbon steel 16 gauge or 18 gauge construction staples, 7/16 crown, 1 crown or 1/4 narrow crown, of specification ASTM F1667, with a wire diameter of at least 1.02 mm (18 gauge) but not exceeding 1.52 mm (16 gauge), with a length of at least 25 mm but not exceeding 60 mm, electro galvanized |
| 330 | 7317.00.00 | Nails, tacks and staples | Carbon steel bulk roofing nails, smooth or spiral shank, round head or #10 flat head, diamond point, of grade 1006 or 1018, of specification ASTM F1667, with a shank diameter of 0.12 inches or 0.148 inches, with a length of at least 1 inch but not exceeding 3.5 inches, electro galvanized or hot-dip galvanized |
| 331 | 7318.12.00 | Fasteners | Structural wood screws with self-tapping tip, of carbon steel of material number 1.5505 or 1.5506 of specification EN 10263-4:2001, or of stainless steel of material number 1.4567 of specification EN 10088-3:2005 or EN 10263-5:2001, case-hardened, with a diameter of at least 6 mm but not exceeding 14 mm, with a length of at least 60 mm but not exceeding 1,500 mm, electroplated with a coating thickness of at least 8 microns but not exceeding 15 microns |
| 332 | 7318.12.00 | Fasteners | Wood screws for construction: drywall screws, deck screws, particle board screws, and general wood-to-wood or wood-to-metal fasteners |
| 333 | 7318.12.00 | Fasteners | Structural wood screws of carbon or stainless steel, self-tapping, diameters 6-14mm, lengths 60-1500mm, for engineered timber (mass timber, CLT, glulam) |
| 334 | 7318.12.00 | Fasteners | Stainless steel (305, 316) bugle-head wood screws with type 17 point, for exterior decking and marine applications |
| 335 | 7318.12.00 | Fasteners | Stainless steel bugle-head decking screws of grade 305 or 316, of specification ASTM F788/F788M, with square drive, type 17 point, in sizes #8 through #12, with a length of at least 1-1/2 inches but not exceeding 4 inches, passivated |
| 336 | 7318.12.00 | Fasteners | Carbon steel, heat-treated, self-tapping structural wood screws, partially threaded, countersunk head, washer head, flat head with shoulder or hex head, Torx or hex drive, self-tapping or self-drilling point, with a nominal diameter of at least 3 mm but not exceeding 16 mm, with a length of at least 16 mm but not exceeding 1000 mm, electrolytic zinc coating with chromate or thick-film passivation, with a salt spray resistance of at least 96 hours per ISO 9227, for use in structural wood-to-wood connections in construction |
| 337 | 7318.12.00 | Fasteners | Carbon steel, heat-treated, self-tapping structural wood screws, fully threaded, cylindrical head, countersunk head, hexagonal star head or reverse star head, Torx or hex drive, self-drilling point, with a nominal diameter of at least 5 mm but not exceeding 14 mm, with a length of at least 70 mm but not exceeding 1500 mm, electrolytic zinc coating with chromate or thick-film passivation, or zinc-nickel alloy coating, with a salt spray resistance of at least 96 hours per ISO 9227, for use in structural wood-to-wood connections in construction |
| 338 | 7318.12.00 | Fasteners | Low-carbon steel, heat-treated, self-tapping structural wood screws, partially threaded, hex washer head, Type 17 drill point, with a nominal diameter of 6.35 mm (1/4 inch), with a length of at least 38 mm but not exceeding 203.2 mm, with a corrosion-resistant coating equivalent to hot-dip galvanization per ASTM A153, Class D, for use in wood-to-wood and steel-to-wood structural connections in construction |
| 339 | 7318.13.00 | Fasteners | Threaded eye bolts and eye screws for load-bearing rigging, lifting, and securing applications (forged or welded) |
| 340 | 7318.13.00 | Fasteners | Screw hooks and screw rings for light-duty hanging: cup hooks, ceiling hooks, L-hooks, wire-formed hooks |
| 341 | 7318.14.00 | Fasteners | Stainless steel self-tapping screws of grade 316, cold-rolled, with a size of No 7 and with a length of 2.375 inches, phosphate coated |
| 342 | 7318.14.00 | Fasteners | Carbon steel self-tapping screws of grade C1022, cold-rolled, with a size of No 7 and with a length of 2.375 inches, coated |
| 343 | 7318.14.00 | Fasteners | Stainless steel wedge clips and edge clips of grade 304, pre-assembled with stainless steel gussets and nylon spacers, with self-tapping screws of a diameter of 0.117 inches, with a length of at least 1.75 inches but not exceeding 2.25 inches, with trim head T15 drive |
| 344 | 7318.14.00 | Fasteners | Carbon steel or stainless steel (grade 304) self-tapping screws with dual reversing pitch threads, chisel point tips and trim head T15 drive, with a diameter of 0.116 inches and with a length of 2.341 inches, loose or collated in plastic strips |
| 345 | 7318.14.00 | Fasteners | Self-tapping structural screws of heat-treated hardened carbon steel, with a core hardness not exceeding 390 HV, with a thread diameter of at least 3.5 mm but not exceeding 5 mm, with a length of at least 20 mm but not exceeding 120 mm, with partial threads and full threads, with shank ribs on partial threads, with countersunk head with milling ribs, with a 6-point star-shaped drive, bright zinc plated |
| 346 | 7318.14.00 | Fasteners | Self-tapping structural screws of heat-treated hardened carbon steel, with a core hardness not exceeding 360 HV, with a thread diameter of at least 6 mm but not exceeding 10 mm, with a length of at least 40 mm but not exceeding 800 mm, with countersunk with milling ribs, flange, cylindrical or hexagon head types, with a 6-point star-shaped drive, bright zinc plated |
| 347 | 7318.14.00 | Fasteners | Self-tapping structural screws of stainless steel of grade A2 (AISI 304Cu), of material number EN 1.4567, with a thread diameter of at least 3.5 mm but not exceeding 8 mm, with a length of at least 30 mm but not exceeding 400 mm, with partial threads or full threads, with shank ribs on partial threads, with countersunk head with milling ribs, with a 6-point star-shaped drive, uncoated |
| 348 | 7318.14.00 | Fasteners | Self-tapping structural screws of stainless steel of grade A2 (AISI 304Cu), of material number EN 1.4567, with a thread diameter of at least 6 mm but not exceeding 8 mm, with a length of at least 40 mm but not exceeding 340 mm, with partial threads or full threads, with flange head, with a 6-point star-shaped drive, uncoated |
| 349 | 7318.14.00 | Fasteners | Self-tapping structural screws of stainless steel of grade A2 (AISI 304Cu), of material number EN 1.4567, with a thread diameter of at least 4.5 mm but not exceeding 5 mm, with a length of at least 40 mm but not exceeding 80 mm, with full threads, with raised countersunk head, with a 6-point star-shaped drive, uncoated |
| 350 | 7318.14.00 | Fasteners | Self-tapping concrete anchor screws of stainless steel of grade A4 (AISI 316), of material number EN 1.4401, with a thread diameter of 7.5 mm, with a length of at least 40 mm but not exceeding 115 mm, with concrete threads, with phosphate tip, with countersunk or pan head, with a 6-point star-shaped drive, uncoated |
| 351 | 7318.14.00 | Fasteners | Self-tapping screws of heat-treated carbon steel of grade 1022 or 10B21, with a diameter of at least No 6 but not exceeding 0.375 inches and with a length of at least 0.5 inches but not exceeding 20 inches, fully or partially threaded, coated |
| 352 | 7318.14.00 | Fasteners | Self-tapping screws of stainless steel of grade 305 or 316, with a diameter of at least No 8 but not exceeding 0.375 inches and with a length of at least 1 inch but not exceeding 8 inches, fully or partially threaded |
| 353 | 7318.14.00 | Fasteners | Steel self-drilling roofing screws, #15 diameter, with truss head, with a length of at least 2 inches but not exceeding 20 inches, corrosion-resistant coated |
| 354 | 7318.14.00 | Fasteners | Self-drilling self-tapping screws of stainless steel of grade 410, machined, heat treated to SAE J933, of specification ASTM C1513, with a diameter of 0.25 inches, with a head diameter of 0.625 inches, with a length of 2.25 inches, with pancake or wafer head, with Phillips drive, with coarse thread, uncoated |
| 355 | 7318.14.00 | Fasteners | Self-tapping screws for automotive body assembly, sheet metal work, and HVAC duct fastening |
| 356 | 7318.14.00 | Fasteners | Self-tapping screws for construction: TEK screws, self-drilling screws for steel framing, roofing, cladding, siding |
| 357 | 7318.14.00 | Fasteners | Steel self-drilling roofing screws (#15), truss or hex washer head, with EPDM sealing washer, for metal roofing and cladding |
| 358 | 7318.14.00 | Fasteners | Self-tapping structural screws for engineered timber connections (CLT, glulam), countersunk or flange head, 6-point star drive |
| 359 | 7318.14.00 | Fasteners | Stainless steel (A4/316) self-tapping concrete anchor screws, with concrete thread and phosphate tip |
| 360 | 7318.14.00 | Fasteners | Stainless steel self-tapping or self-drilling screws of grade 410 or 18-8 (304), of specification ASTM F788/F788M or ASME, pan head, truss head, hex washer head or flat head, square drive, Phillips drive or socket drive, in sizes #8 through 1/4-14, with a length of at least 1/2 inch but not exceeding 3 inches, passivated or with proprietary corrosion-resistant coating |
| 361 | 7318.15.00 | Fasteners | Stainless steel hex bolts, heavy hex bolts, hex cap screws and machine screws of grade 18-8 (304) or 316, of specification ASTM A193 B8M Class 1, ASTM F593 or ASME B18.2.1, in sizes 1/4-20 through 3/4-10, with a length of at least 2 inches but not exceeding 10 inches, passivated |
| 362 | 7318.15.00.10 | Fasteners | Steel square head set screws with hardened cup point, with a thread size of 3/8-16, with a length of at least 1 inch but not exceeding 1 1/4 inches, zinc plated body with painted tip |
| 363 | 7318.15.00.10 | Fasteners | Carbon steel set screws (square head or hex socket, cup point), zinc plated, for locking shafts, collars, and machine components |
| 364 | 7318.15.00.42 | Fasteners | Carbon steel, alloy steel or stainless steel heavy hex bolts, blank, fully-threaded or partially-threaded, of grade B7, B7M or B16 of specification ASTM A193/ASME SA193, or of grade B6, B8, B8C, B8T or B8M of specification ASTM A320/ASME SA320, or of grade 304 or 316, with a diameter of at least 0.25 inches but not exceeding 4 inches, with a length of at least 0.5 inches but not exceeding 24 inches, with UNC or 8UN threading of Class 2A/2B fit, plain, trivalent zinc plated, fluoropolymer coated, hot-dip galvanized to ASTM A153 or passivated |
| 365 | 7318.15.00.42 | Fasteners | Carbon/alloy steel hex bolts and heavy hex bolts (ASTM A307, A325, A490, A193), partially or fully threaded, plain/zinc/galvanized |
| 366 | 7318.15.00.45 | Fasteners | Carbon steel, alloy steel or stainless steel fully-threaded rod and studs, of grade B7, B7M or B16 of specification ASTM A193/ASME SA193, of grade L7, L7M, B6, B8, B8C, B8T or B8M of specification ASTM A320/ASME SA320, of grade BD or BC of specification ASTM A354, of grade 2 of specification ASTM A307, of specification ASTM F1554-55, or of grade 304 or 316, with a diameter of at least 0.25 inches but not exceeding 4 inches, with a length of at least 0.5 inches but not exceeding 144 inches, plain, trivalent zinc plated, fluoropolymer coated, hot-dip galvanized to ASTM A153 or passivated |
| 367 | 7318.15.00.45 | Fasteners | Carbon, alloy, or stainless steel fully threaded rod and studs (ASTM A193, A320, A354, A307, F1554, all grades), all diameters and lengths |
| 368 | 7318.15.00.49 | Fasteners | Steel hardware kit, consisting of hex nuts (3/8-16 and 5/16-18), open eye bolts (5/16-18 by 3 3/4 inches) and S hooks (1/4 by 2 inches), steel |
| 369 | 7318.15.00.49 | Fasteners | Steel hardware kit, consisting of machine screws (#10-24), self-tapping screws (1/4-14 and 1/4-20), ribbed neck track bolts (1/4-20 by 9/16 inch), hex flanged nuts (1/4-20) and plain washers (1/4 inch), steel |
| 370 | 7318.15.00.49 | Fasteners | Carbon steel shoulder-type eye bolts of grade C1030/C1035, of specification ASTM A489, ANSI B18.15 and MS51937, with a thread size of at least 1/4-20 but not exceeding 2-4 1/2, with a shank length of at least 1 inch but not exceeding 6 inches, with an eye inside diameter of at least 3/4 inch but not exceeding 3 3/8 inches, with an eye outside diameter of at least 1 3/16 inches but not exceeding 6 7/8 inches, with an overall length of at least 2 3/8 inches but not exceeding 11 7/8 inches, with a rated capacity of at least 650 lbs but not exceeding 40,000 lbs, uncoated, zinc plated or galvanized |
| 371 | 7318.15.00.49 | Fasteners | Carbon steel plain-type eye bolts of grade C1030/C1035, of specification ASTM A489 and ANSI B18.15, with a thread size of at least 1/4-20 but not exceeding 2-4 1/2, with a shank length of at least 1 inch but not exceeding 4 inches, with an eye inside diameter of at least 3/4 inch but not exceeding 3 3/8 inches, with an eye outside diameter of at least 1 3/16 inches but not exceeding 6 7/8 inches, with an overall length of at least 2 7/32 inches but not exceeding 11 inches, with a rated capacity of at least 650 lbs but not exceeding 40,000 lbs, uncoated or zinc plated |
| 372 | 7318.15.00.49 | Fasteners | Carbon steel alloy-type eye bolts of grade C1030/C1035, of specification ASTM F541 and ANSI B18.15, with a thread size of at least 3/8-16 but not exceeding 2-4 1/2, with a shank length of at least 1 1/4 inches but not exceeding 4 inches, with an eye inside diameter of at least 1 inch but not exceeding 3 1/4 inches, with an eye outside diameter of at least 1 21/32 inches but not exceeding 6 7/8 inches, with an overall length of at least 3.28 inches but not exceeding 11.88 inches, with a rated capacity of at least 1,480 lbs but not exceeding 47,600 lbs, uncoated |
| 373 | 7318.15.00.49 | Fasteners | Carbon steel carriage bolts with hex nuts, of grade ASTM A307 Grade A, with a round mushroom head with square neck to ASME B18.5, with a bolt diameter of at least 7.9 mm but not exceeding 9.5 mm, with a bolt length of at least 25 mm but not exceeding 89 mm, with UNC Class 2A thread, hot-dip galvanized to ASTM A153 Class C, black powder coated, electro-zinc plated with black topcoat, or zinc flake coated with organic topcoat |
| 374 | 7318.15.00.49 | Fasteners | Carbon steel hinge bolts with or without collar, of grade ASTM A307 Grade A, with standard end or machined ball end, with a bolt diameter of at least 12.7 mm but not exceeding 25.4 mm, with a bolt length of at least 127 mm but not exceeding 305 mm, with UNC Class 2A thread, hot-dip galvanized to ASTM A153 Class C, black powder coated, or electro-zinc plated with black topcoat |
| 375 | 7318.15.00.49 | Fasteners | Carbon steel lag hinge bolts with collar, with lag thread at one end and machine thread at the other, of grade ASTM A307 Grade A or equivalent, with a diameter of at least 12.7 mm but not exceeding 19.1 mm, with an overall length of at least 127 mm but not exceeding 152 mm, with lag thread to ASME B18.2.1 and machine thread UNC Class 2A, hot-dip galvanized to ASTM A153 Class C, black powder coated, or electro-zinc plated with black topcoat |
| 376 | 7318.15.00.49 | Fasteners | Carbon steel cane bolts (drop rods) with guide brackets, of grade ASTM A36 or ASTM A307 Grade A, in 1-pin or 2-pin configuration, with a diameter of at least 12.7 mm but not exceeding 19.1 mm, with a length of at least 610 mm but not exceeding 914 mm, with UNC Class 2A thread, with carbon steel guide brackets of grade ASTM A36, hot-dip galvanized to ASTM A153 Class C, black powder coated, or electro-zinc plated with black topcoat |
| 377 | 7318.15.00.49 | Fasteners | Carbon steel U-bolts and square U-bolts, of grade ASTM A36, with a bar diameter of 11 mm, with an inside width of at least 76 mm but not exceeding 114 mm, with a thread length per leg of at least 25.4 mm, with UNC Class 2A thread, hot-dip galvanized to ASTM A153 Class C or black powder coated |
| 378 | 7318.15.00.49 | Fasteners | Carbon steel turnbuckles of specification ASTM F1145, with hook-and-hook or jaw-and-jaw end fittings, open body construction, with a body diameter of 7.9 mm, with an extended length of 102 mm, with UNC right-hand and left-hand threaded ends, hot-dip galvanized to ASTM A153 Class C |
| 379 | 7318.15.00.49 | Fasteners | Carbon steel carriage bolts (ASTM A307), round mushroom head with square neck, ASME B18.5, galvanized or powder coated |
| 380 | 7318.15.00.49 | Fasteners | Carbon steel shoulder-type, plain-type, and alloy-type eye bolts (ASTM A489, F541, ANSI B18.15), for overhead lifting and rigging |
| 381 | 7318.15.00.49 | Fasteners | Carbon steel hinge bolts, lag hinge bolts, and cane bolts (drop rods) with guide brackets, for gate and door hinge applications |
| 382 | 7318.15.00.49 | Fasteners | Carbon steel U-bolts (ASTM A36) and turnbuckles (ASTM F1145), hook-hook or jaw-jaw, for pipe clamping, gate bracing, and light rigging |
| 383 | 7318.15.00.49 | Fasteners | Carbon steel fencing hardware kits (hex nuts, eye bolts, S-hooks, track bolts, flanged nuts, washers), for fence panel and gate installation |
| 384 | 7318.16.00 | Fasteners | Open-end threaded rivet nuts of steel of grade AISI 1016 or AISI 1018, with a half-hexagonal formed body, with a thread size of 1/4-20, with a grip range of at least 0.03 inches but not exceeding 0.17 inches, with a head diameter of 0.51 inches, with a head height of 0.03 inches, with an uninstalled height of 0.59 inches, with an installed height of 0.40 inches, with a thread diameter of 0.25 inches, with a hex across-flats dimension of 0.75 inches and with a head radius of 0.04 inches, trivalent zinc with trivalent chromate coated |
| 385 | 7318.16.00.10 | Fasteners | Steel or stainless steel shaft locknuts, precision turned or cold-formed, of series N, AN, KM, KML or HM, in metric and inch thread sizes, coated or uncoated |
| 386 | 7318.16.00.10 | Fasteners | Alloy steel wheel lock nuts with integrated wedge-locking cam mechanisms, of grade EN 1.7182, sized for thread diameters of at least M16 but not exceeding M24, with an inner diameter of 15.2 mm, with an outer diameter of at least 29.8 mm but not exceeding 29.9 mm and with a thickness of 3.15 mm, zinc flake coated |
| 387 | 7318.16.00.10 | Fasteners | All-metal lock nuts and flex-type lock nuts for high-temperature and high-vibration applications |
| 388 | 7318.16.00.10 | Fasteners | Nylon-insert lock nuts (prevailing torque type) for vibration-resistant assemblies in automotive, aerospace, and industrial equipment |
| 389 | 7318.16.00.90 | Fasteners | Steel blind rivet nuts with a thread size of 3/8, with a body diameter of 16 mm, with a body length of 17 mm, zinc plated |
| 390 | 7318.16.00.90 | Fasteners | Carbon steel, alloy steel or stainless steel heavy hex nuts, of grade 2H, 2HM or 7L of specification ASTM A194/ASME SA194, of grade L7 or L7M of specification ASTM A194/ASME SA194, or of grade B6, B8, B8C, B8T, B8M, 8 (304) or 8M (316) of specification ASTM A194/ASME SA194, with a diameter of at least 0.25 inches but not exceeding 4 inches, plain, trivalent zinc plated, fluoropolymer coated, hot-dip galvanized to ASTM A153 or passivated |
| 391 | 7318.16.00.90 | Fasteners | Carbon, alloy, or stainless steel hex nuts and heavy hex nuts (ASTM A194, A563, all grades), for general bolted assemblies |
| 392 | 7318.16.00.90 | Fasteners | Carbon or stainless steel blind rivet nuts (threaded inserts), for creating threaded connections in sheet metal and thin-wall assemblies |
| 393 | 7318.19.00 | Fasteners | Steel adapter and withdrawal sleeves for bearing assemblies, of grade 52100, of series H, H2, HE, HA, HS, KM, AH, AHX and stepped sleeves, in metric and inch bore dimensions, coated or uncoated |
| 394 | 7318.19.00 | Fasteners | Carbon steel concrete wedge anchors and sleeve anchors, of grade ASTM F1554 Grade 36, with a diameter of at least 7.9 mm but not exceeding 12.7 mm, with a length of at least 64 mm but not exceeding 102 mm, with UNC Class 2A thread, plain or zinc electroplated |
| 395 | 7318.19.00 | Fasteners | Carbon, alloy, or stainless steel fully threaded rod (all grades), all diameters and lengths, for mechanical and structural connections, pipe hanging, anchoring |
| 396 | 7318.19.00 | Fasteners | Carbon steel concrete wedge anchors and sleeve anchors, zinc or plain, for anchoring to concrete and masonry |
| 397 | 7318.19.00 | Fasteners | Stainless steel or alloy steel fully threaded rod of grade A193 B8M Class 1 (316 stainless) or A193 B7 (alloy steel), of specification ASME B18.31.3, in diameters 3/4 through 2 inches, with a length of 6 feet or 12 feet, passivated, hot-dip galvanized or plain, both ends painted for grade identification |
| 398 | 7318.21.00 | Fasteners | Steel or stainless steel tab washers and locking plates for bearing locknuts, of series MB, W and TW, including bent tab and tang types, in metric and inch shaft sizes, coated or uncoated |
| 399 | 7318.21.00 | Fasteners | Alloy steel or stainless steel wedge-locking washer pairs with radial serrations and cam faces, assembled as mating components, of grade EN 1.4404, EN 1.4547, EN 1.7182 or EN 1.7225, sized for thread diameters of at least M3 but not exceeding M130, with an inner diameter of at least 3.40 mm but not exceeding 133.40 mm, with an outer diameter of at least 7 mm but not exceeding 178 mm and with a pair thickness of at least 1.8 mm but not exceeding 9.5 mm, zinc flake coated or uncoated |
| 400 | 7318.21.00 | Fasteners | Steel Belleville washers of specification DIN 2093, with an inside diameter of 16.3 mm, with an outside diameter of 31.5 mm, black phosphate coated |
| 401 | 7318.21.00 | Fasteners | Carbon steel split lock washers (ASME B18.21.1 / DIN 127B), zinc or mechanical galvanized, all standard sizes |
| 402 | 7318.21.00 | Fasteners | Alloy steel Grade 8 split lock washers, yellow zinc, for high-strength bolted assemblies |
| 403 | 7318.21.00 | Fasteners | Carbon or stainless steel external and internal tooth lock washers (DIN 6797A/J), for electrical connections and anti-rotation |
| 404 | 7318.21.00 | Fasteners | Alloy or stainless steel wedge-locking washer pairs with radial serrations and cam faces, for vibration-critical bolted joints |
| 405 | 7318.21.00 | Fasteners | Steel Belleville (disc spring) washers (DIN 2093) and wave washers, for preload and vibration damping in assemblies |
| 406 | 7318.21.00 | Fasteners | Stainless steel (18-8 / 316) split lock washers, for corrosion-resistant assemblies in marine and chemical environments |
| 407 | 7318.21.00 | Fasteners | Carbon steel split lock washers (helical spring type) of grade SAE J403 1055-1065, of specification ASME B18.21.1, with a hardness of 38 to 46 HRC, in sizes #6 through 1-1/2 inches, zinc clear, zinc yellow, mechanical zinc, plain or black oxide finish |
| 408 | 7318.21.00 | Fasteners | Alloy steel Grade 8 split lock washers (helical spring type) of grade SAE J403 1055-1065, of specification ASME B18.21.1, with a hardness of 38 to 46 HRC, in sizes 1/4 through 1 inch, zinc yellow finish |
| 409 | 7318.21.00 | Fasteners | Carbon steel split lock washers (helical spring type) of grade CK 60, of specification DIN 127B and DIN 17222, with a hardness of 430 to 530 HV, in metric sizes M2 through M20, zinc clear, zinc yellow, zinc trivalent or plain finish |
| 410 | 7318.21.00 | Fasteners | Stainless steel split lock washers (helical spring type) of grade 18-8 (304) or 316, of specification ASME B18.21.1 or DIN 127B, in imperial sizes #4 through 3/4 inch or metric sizes M2.5 through M16, passivated, black oxide or uncoated |
| 411 | 7318.21.00 | Fasteners | Carbon steel or stainless steel external tooth and internal tooth lock washers, of grade CK 60 (DIN 17222) or 304 stainless steel, of specification DIN 6797A (external), DIN 6797J (internal) or ASME, with a hardness of 350 to 425 HV (steel), in imperial sizes 5/16 through 3/4 inch or metric sizes 2.5 through 8 mm, zinc or passivated |
| 412 | 7318.21.00 | Fasteners | Carbon steel wave or curved spring washers of grade CK 60, of specification DIN 137B and DIN 17222, with a hardness of 430 to 530 HV, in metric sizes M5 through M12, nickel or zinc yellow finish |
| 413 | 7318.21.00 | Fasteners | Stainless steel wedge-locking washer pairs with radial serrations and cam faces (Sperrkant type), of grade A4/316, assembled as mating pairs, in metric sizes M6 through M8 |
| 414 | 7318.21.00 | Fasteners | Carbon steel heavy-duty spring lock washers of specification 1967 AREA, with a burnished and light oil finish, in sizes 7/8 through 1-3/8 inches |
| 415 | 7318.21.00 | Fasteners | Carbon steel high-collar helical spring lock washers of grade SAE J403 1055-1065, of specification ASME, with a hardness of 38 to 46 HRC, mechanical zinc finish |
| 416 | 7318.21.00 | Fasteners | Stainless steel spring lock washers of grade A2/304, of specification DIN 7980, in metric size M3 |
| 417 | 7318.21.00 | Fasteners | Carbon steel double-toothed lock washers of grade CK 60, of specification DIN 17222, with a hardness of 430 to 530 HV, plain finish |
| 418 | 7318.22.00 | Fasteners | Carbon steel flat washers (SAE narrow, USS wide), zinc plated, all standard imperial and metric sizes |
| 419 | 7318.22.00 | Fasteners | Carbon or stainless steel fender washers (oversized OD), zinc plated |
| 420 | 7318.22.00 | Fasteners | Hardened steel structural washers (ASTM F436), plain or galvanized, for use with A325/A490 structural bolts |
| 421 | 7318.22.00 | Fasteners | Stainless steel (18-8 / 316) flat washers, for corrosion-resistant assemblies |
| 422 | 7318.22.00 | Fasteners | Steel bevel washers for use on channel flanges and I-beams with structural bolts |
| 423 | 7318.22.00 | Fasteners | Stainless steel or hardened carbon steel flat washers, fender washers, finish washers and bevel washers of grade 18-8 (304), 316 or ASTM F436 (hardened steel), in sizes #10 through 3/4 inch, passivated or galvanized |
| 424 | 7318.22.00 | Fasteners | Carbon steel precision shim washers of grade C60, of specification DIN 988, plain finish |
| 425 | 7318.23.00 | Fasteners | Blind rivets (pop rivets) and structural blind rivets for sheet metal, HVAC ductwork, automotive body assembly, and light construction |
| 426 | 7318.23.00 | Fasteners | Solid rivets, drive rivets, and semi-tubular rivets for heavy structural, aerospace, and industrial assembly |
| 427 | 7318.24.00 | Fasteners | Cotters and cotter-pins (split pins) for pin retention in automotive, agricultural, marine, and machinery applications |
| 428 | 7318.29.00 | Fasteners | Deck board fasteners composed of a nylon spacer body and stainless steel gussets and screws of grade 305, cold-rolled, with a spacer body width of 1.88 inches, a height of 1.38 inches and a thickness of 0.19 inches, with a gusset width of 0.31 inches, a height of 0.69 inches and a thickness of 0.13 inches, with a screw size of No 7 and a length of 1.75 inches |
| 429 | 7318.29.00 | Fasteners | Deck board fasteners composed of a nylon spacer body and stainless steel gussets and screws of grade 316, cold-rolled, with a spacer body width of 1 inch, a height of 0.5 inches and a thickness of 0.69 inches, with a gusset width of 0.31 inches, a height of 0.69 inches and a thickness of 0.13 inches, with a screw size of No 7 and a length of 1.75 inches |
| 430 | 7318.29.00 | Fasteners | Steel roofing stress distribution plates, stamped, round or square, zinc-aluminum alloy coated or with proprietary coating, with a diameter or width of at least 2 3/8 inches but not exceeding 3 3/8 inches, with a thickness of at least 0.024 inches (24 gauge) but not exceeding 0.035 inches (22 gauge) |
| 431 | 7318.29.00 | Fasteners | Clevis pins, dowel pins, taper pins, spring pins (roll pins), and similar machine-element retention pins |
| 432 | 7318.29.00 | Fasteners | Retaining rings (snap rings, circlips), hitch pins, lynch pins, and similar fastening/retention hardware |
| 433 | 7318.29.00 | Fasteners | Deck board fasteners of nylon spacer body with stainless steel gussets and screws, for hidden decking installation |
| 434 | 7318.29.00 | Fasteners | Steel stress distribution plates (stamped, round or square), zinc-aluminum coated, for mechanically attached single-ply roofing |
| 435 | 7318.29.00 | Fasteners | Steel retaining rings (snap rings, circlips), E-rings, C-clips, and push-on fasteners for shaft and bore retention in machinery |
| 436 | 7318.29.00 | Fasteners | Carbon steel or stainless steel retaining rings, circlips, E-rings, C-clips, K-rings, V-rings, crescent rings, bowed rings and push-on fasteners, of grade CK 60 (DIN 17222), SAE 1060-1090 or 304 stainless steel, of specification DIN 471, DIN 983, DIN 6799, DIN 7993 or equivalent, with a hardness of 430 to 530 HV (steel) or RC 47-52 (SAE), in imperial sizes 3/16 through 3-1/4 inches or metric sizes 7 through 100 mm, phosphate and oil, plain or passivated |
| 437 | 7320.10.00 | Springs | Leaf springs for railcar suspension and industrial shock absorption applications |
| 438 | 7320.10.00 | Springs | Leaf springs and individual leaves for vehicle suspension: truck, trailer, and heavy equipment; parabolic and multi-leaf assemblies |
| 439 | 7320.20.00.10 | Springs | Bonnell coil spring units: open-coil interconnected spring systems for innerspring mattress manufacturing |
| 440 | 7320.20.00.10 | Springs | Pocket coil (individually wrapped) spring units for premium mattress manufacturing; requires specialized encasement machinery |
| 441 | 7320.20.00.10 | Springs | Springs for upholstered seating: sinuous (zigzag) springs, seat coil springs, recliner mechanism springs, sofa support springs |
| 442 | 7320.20.00.20 | Springs | Helical springs for motor vehicle engines and drivetrain: valve springs, clutch springs, brake return springs |
| 443 | 7320.20.00.20 | Springs | Helical (coil) springs for motor vehicle suspension: front and rear suspension coil springs |
| 444 | 7320.20.00.90 | Springs | Helical springs for agricultural equipment: tillage, seeding, and harvesting machinery springs |
| 445 | 7320.20.00.90 | Springs | Helical springs for garage door counterbalance systems: torsion springs and extension springs |
| 446 | 7320.20.00.90 | Springs | Industrial helical springs: compression springs, extension springs, torsion springs, die springs for tooling and stamping |
| 447 | 7325.91.00.10 | Articles of cast iron and steel | Cast iron pipe fittings: flanged fittings, threaded fittings, and grooved couplings for water, sewer, and industrial piping |
| 448 | 7325.91.00.10 | Articles of cast iron and steel | Cast iron counterweights, ballast blocks, and general-purpose industrial castings |
| 449 | 7325.91.00.10 | Articles of cast iron and steel | Cast iron grinding media: balls, cylpebs, and rods for mining mills, cement mills, and mineral processing |
| 450 | 7325.91.00.10 | Articles of cast iron and steel | Cast iron manhole covers, frames, gratings, trench covers, and drainage/infrastructure castings |
| 451 | 7325.91.00.90 | Articles of cast iron and steel | Cast steel grinding media and wear parts: mill liners, crusher wear components, abrasion-resistant castings |
| 452 | 7325.91.00.90 | Articles of cast iron and steel | General-purpose cast steel articles: industrial castings for heavy equipment, infrastructure, and manufacturing |
| 453 | 7326.20.00 | Other articles of iron or steel | Fibres d’acier regroupées en bandes au moyen d’un liant hydrosoluble, de spécification ASTM A820, EN 14889-1 et ISO 13270 classe A, ayant des dimensions transversales d’au moins 0,75 mm mais n’excédant pas 0,90 mm, une résistance nominale à la traction de 2 200 MPa, un module de Young de 210 000 MPa, un allongement à la rupture de 0,8 % et un réseau de 4 644 fibres/kg, finition brillante |
| 454 | 7326.20.00 | Other articles of iron or steel | Fabricated wire articles for industrial use: wire baskets, wire forms, cable trays, and custom wire assemblies |
| 455 | 7326.20.00 | Other articles of iron or steel | Wire display racks, wire shelving components, point-of-purchase displays, and retail wire fixtures |
| 456 | 7326.20.00 | Other articles of iron or steel | Wire reinforcing cages, wire lath, cable ties, and wire assemblies for construction and concrete reinforcement |
| 457 | 7326.90.10 | Other articles of iron or steel | Carbon steel tube thimble with incorporated forged master link, formed and bent, hot-dip galvanized, with a thimble inside diameter of 94 mm, with a thimble outside diameter of 114 mm and with a thimble length of 460 mm, with a master link diameter of 38 mm, with a master link outside length of 267 mm, with a master link outside width of 211 mm, with a master link inside length of 267 mm and with a master link inside width of 135 mm |
| 458 | 7326.90.10 | Other articles of iron or steel | Forged alloy steel shackle with screw pin, heat-treated, hot-dip galvanized and powder coated, with a lift capacity of 35 tonnes, with a body diameter of at least 51 mm but not exceeding 122 mm, with bore hole diameters of 57 mm, with a screw pin length of 188 mm, with an overall height of 340 mm, with an overall width of 249 mm, with an inside top opening of 146 mm and with an inside bottom opening of 86 mm |
| 459 | 7326.90.10 | Other articles of iron or steel | Climbing and mountaineering hardware: carabiners, pitons, ascenders, and related steel articles |
| 460 | 7326.90.10 | Other articles of iron or steel | Steel articles for commercial fishing: net-spreading swivels, trawl components, and marine plant harvesting gear |
| 461 | 7326.90.10 | Other articles of iron or steel | Oilfield sucker-rod couplings, pony-rod couplings, polished-rod couplings; fishing tools for oil, gas, and potash well operations |
| 462 | 7326.90.10 | Other articles of iron or steel | Other specialized articles: debris chute clevis hooks; migratory bird identification bands; pitless well heads and parts |
| 463 | 7326.90.10 | Other articles of iron or steel | Carbon steel tube thimbles with incorporated forged master link, hot-dip galvanized, for wire rope termination in marine mooring and heavy lifting |
| 464 | 7326.90.10 | Other articles of iron or steel | Forged alloy steel shackles with screw pin, heat-treated, galvanized and powder coated, for heavy-lift marine and offshore mooring |
| 465 | 7326.90.90.90 | Other articles of iron or steel | Shackles of alloy steel, closed-die forged and quenched and tempered, with a diameter range of 0.1875 inches to 2.500 inches, covering standard and wide opening mooring shackles, galvanized. Manufactured in accordance with RR-C-271D, Type IVA, Grade A, Class 2. ASME B30.26. High Tensile Steel, Forged-Quenched and Tempered, Grade 6 |
| 466 | 7326.90.90.90 | Other articles of iron or steel | Pear-shaped connecting links of alloy steel, with a diameter of at least 25 mm but not exceeding 40 mm, painted. Manufactured in accordance with RR-C-271F |
| 467 | 7326.90.90.90 | Other articles of iron or steel | Eye and eye swivels of alloy steel, with a diameter of at least 0.375 inches but not exceeding 1.500 inches, galvanized. Forged-Quenched and tempered. Manufactured in accordance with RR-C-271F, Type VII, Class 2 |
| 468 | 7326.90.90.90 | Other articles of iron or steel | Thimbles of alloy steel, with a diameter of at least 0.25 inches but not exceeding 2.250 inches, galvanized. Manufactured in accordance with FF-T-276C |
| 469 | 7326.90.90.90 | Other articles of iron or steel | Tube thimbles with integrated master link of alloy steel, with a tube diameter of at least 65 mm but not exceeding 105 mm and an integrated master link diameter of at least 28 mm but not exceeding 36 mm, galvanized. Manufactured in accordance with FF-T-276C |
| 470 | 7326.90.90.90 | Other articles of iron or steel | S-hooks of carbon steel, with dimensions of 6 mm by 55 mm or 8 mm by 76 mm, zinc plated |
| 471 | 7326.90.90.90 | Other articles of iron or steel | Steel horseshoes of grade ASTM A36 or AISI 1018, forged, with a thickness of at least 6.5 mm but not exceeding 13 mm, with a width of at least 15 mm but not exceeding 33 mm and with a heel-to-heel circumference of at least 175 mm but not exceeding 600 mm, uncoated |
| 472 | 7326.90.90.90 | Other articles of iron or steel | Mild steel plates of specification ASTM A36, cold drawn, with a height of 22 mm or 26 mm, with a width of 48 mm, with a length of 46.75 inches and with three 8 mm diameter holes, with an outer PVC tube |
| 473 | 7326.90.90.90 | Other articles of iron or steel | Mild steel bars of specification ASTM A36, cold drawn, with a height of 22 mm, with a width of 38 mm, with a length of 20.75 inches, 22.25 inches or 23.75 inches and with two 12 mm diameter holes, PVC coated |
| 474 | 7326.90.90.90 | Other articles of iron or steel | Cast iron ballast ingots of specification ASTM A48, cast, with a height of 42 mm, with a width of 44 mm and with a length of 207 mm, polyethylene powder coated |
| 475 | 7326.90.90.90 | Other articles of iron or steel | Steel turnbuckle assemblies of grade AISI 1045 of specification ASTM A668 Grade D or Grade F, assembled, quenched and tempered, with a diameter of at least 3 inches but not exceeding 4 inches and with a length of 39 inches, zinc coated |
| 476 | 7326.90.90.90 | Other articles of iron or steel | Manches tubulaires en acier non allié laminé à froid de nuance DC01 +C690, de spécification EN 10139, écroui, d'une résistance à la traction d'au moins 690 MPa, d'un diamètre d'au moins 21 mm mais n'excédant pas 24 mm, d'une longueur d'au moins 1 200 mm mais n'excédant pas 1 370 mm et d'une épaisseur de paroi d'au moins 0,71 mm mais n'excédant pas 0,86 mm, revêtus de polypropylène |
| 477 | 7326.90.90.90 | Other articles of iron or steel | Low alloy steel cast rigging components for forestry applications, of grade 80-50, of specification ASTM A148, cast, spheroidized annealed, with a width of 0.75 inches, with a length of 6 inches and with a diameter of 1 inch, painted |
| 478 | 7326.90.90.90 | Other articles of iron or steel | Low alloy steel cast and welded rigging components for forestry applications, of grade 80-50, of specification ASTM A148, cast and welded, spheroidized annealed, with a width of 0.625 inches and with a length of 6 inches, painted |
| 479 | 7326.90.90.90 | Other articles of iron or steel | Cold-forged stainless steel conveyor belt fasteners of grade 316 with stainless steel or carbon steel staples, with or without polyurethane foam molded in loop area, for belts with a thickness of at least 5 mm but not exceeding 20 mm and with a belt strength not exceeding 4,000 kN/m |
| 480 | 7326.90.90.90 | Other articles of iron or steel | Stainless steel ceiling support (flange) for electrical conduits, uncoated |
| 481 | 7326.90.90.90 | Other articles of iron or steel | Galvanized steel ratchets for garage door tensioners, in left or right orientation, with slotted spring pin of black oxide finished steel |
| 482 | 7326.90.90.90 | Other articles of iron or steel | Steel shaft collars, with an inside diameter of 1 inch, with an outside diameter of 1.485 inches, with a width of 0.495 inches, with 1 or 2 set screws of 5/16 inch thread (screws not included), zinc plated |
| 483 | 7326.90.90.90 | Other articles of iron or steel | Steel threaded shaft clamp, with dimensions of 2.031 inches by 1.986 inches by 0.236 inches, zinc plated |
| 484 | 7326.90.90.90 | Other articles of iron or steel | U-shaped steel ceiling rail bracket of grade Q235, with 5/16-18 conduit mounting screw, zinc plated |
| 485 | 7326.90.90.90 | Other articles of iron or steel | Forged alloy steel shackles (anchor, chain, bolt-type), quenched and tempered, RR-C-271D/ASME B30.26, galvanized, for marine mooring and heavy lifting |
| 486 | 7326.90.90.90 | Other articles of iron or steel | Alloy steel pear-shaped connecting links, eye-and-eye swivels, and anchor chain joining hardware, RR-C-271F, for marine mooring systems |
| 487 | 7326.90.90.90 | Other articles of iron or steel | Alloy or carbon steel thimbles and tube thimbles (with or without integrated master link), FF-T-276C, galvanized, for wire rope termination |
| 488 | 7326.90.90.90 | Other articles of iron or steel | Low-alloy steel cast and welded rigging components for forestry (choker knobs, butt rigging), ASTM A148 |
| 489 | 7326.90.90.90 | Other articles of iron or steel | Steel horseshoes (ASTM A36 or AISI 1018), forged, various sizes and profiles, for farrier and equine applications |
| 490 | 7326.90.90.90 | Other articles of iron or steel | Cold-forged stainless steel conveyor belt fasteners (grade 316) with staples, for belt splicing in mining, aggregate, and food processing |
| 491 | 7326.90.90.90 | Other articles of iron or steel | Steel turnbuckle assemblies (ASTM A668), jaw-jaw/hook-hook/eye-eye, quenched and tempered, zinc coated, for tensioning and bracing |
| 492 | 7326.90.90.90 | Other articles of iron or steel | Carbon steel S-hooks, zinc plated, for general hanging and connecting applications |
| 493 | 7326.90.90.90 | Other articles of iron or steel | Cast iron ballast ingots (ASTM A48), for counterweight, marine, and industrial ballast applications |
| 494 | 7326.90.90.90 | Other articles of iron or steel | Steel shaft collars and threaded shaft clamps, set-screw or clamping type, for power transmission and machinery shaft retention |
| 495 | 7326.90.90.90 | Other articles of iron or steel | Steel ceiling support flanges, U-shaped rail brackets, and conduit mounting hardware for electrical and mechanical installations |
| 496 | 7326.90.90.90 | Other articles of iron or steel | Forged carbon steel or alloy steel pin coupler shackles and rated screw pin anchor shackles, with a nominal size of at least 8 mm but not exceeding 22 mm, clear lacquer or hot-dip galvanized coated, for use as tire chain connecting hardware |
| 497 | 7326.90.90.90 | Other articles of iron or steel | Forged alloy steel forestry track bar profiles, track locks, and replacement studs, with studs of at least 20 mm but not exceeding 30 mm thickness, grey paint or clear lacquer coated, for use as traction and tire protection systems on forestry equipment |
| 498 | 7614.10.00 | Wire rope and cables | ACSR (aluminum conductor steel reinforced) cables for high-voltage electrical power transmission and distribution lines |
| 499 | 7614.10.00 | Wire rope and cables | Steel-reinforced aluminum guy wire, messenger wire, and overhead ground wire for power line and telecom pole support |
| 500 | 8302.41.90 | Garage door hardware | Steel adjustable operator reinforcement brackets for garage doors, two-piece sliding design, with a total length of at least 15 inches but not exceeding 24 inches, with pin, bolt and nut hardware, galvanized |
| 501 | 8302.41.90 | Base metal fittings | Steel counterbalancing system support with 3/8 inch cable, left orientation, zinc plated |
| 502 | 8302.41.90 | Garage door hardware | Steel T-handle flush-mount locking bolt for garage doors, with a length of 3 1/4 inches |
| 503 | 8302.41.90 | Garage door hardware | Steel garage door emergency release plunger assembly, consisting of steel housing, press steel ball bearing, steel spacer and plunger spring, zinc plated |
| 504 | 8302.41.90 | Garage door hardware | Steel top bracket and hinge kit for sectional garage doors, consisting of 1 steel hinge and 2 adjustable steel brackets, with an adjustable bracket length of at least 18 inches but not exceeding 24 inches, zinc plated |
| 505 | 8302.41.90 | Garage door hardware | Cast steel garage door endlock, zinc plated |
| 506 | 8302.41.90 | Garage door hardware | Steel garage door spreader bar with press steel ball bearing, with dimensions of 3.38 inches by 12.5 inches, zinc plated |
| 507 | 8302.41.90 | Garage door hardware | Steel garage door rollers with nylon roller head, with a precision ball bearing (6200, 6201 or 6203 series), with a roller head diameter of at least 1.7 inches but not exceeding 3 inches, with a steel stem diameter of 0.43 inches and with a stem length of at least 4 inches but not exceeding 9 inches, zinc plated |
| 508 | 8302.41.90 | Gate and door hardware | Cast iron and carbon steel decorative gate and door hardware fittings, including spring door handles, pull handles, gate handles, door knockers and door studs, with a length of at least 20 mm but not exceeding 229 mm, black powder coated |
| 509 | 8302.41.90 | Gate and door hardware | Carbon steel spring-loaded self-closing gate closure hardware assemblies, with compression spring mechanism, in single drive and double drive configurations, with mounting hardware, with a bolt diameter of at least 12.7 mm but not exceeding 19.1 mm, hot-dip galvanized to ASTM A153, black powder coated, zinc electroplated, or electro-zinc plated with black topcoat |
| 510 | 8302.41.90.31 | Garage door hardware | Steel spring repair block with 2 set screws, with dimensions of 1.5 inches by 1.83 inches, with set screws of 3/8-16 by 1 inch, zinc plated with painted heads |
| 511 | 8302.41.90.31 | Garage door hardware | Cast steel chain hoist support brackets, with dimensions of at least 3.54 inches by 2.72 inches but not exceeding 3.54 inches by 2.77 inches, zinc plated |
| 512 | 8302.41.90.31 | Garage door hardware | Steel door stop block (flat bar), with dimensions of 1 inch by 6.25 inches by 0.225 inches, uncoated |
| 513 | 8302.41.90.31 | Garage door hardware | Steel retaining spring assemblies, in left, right or universal orientation, with retractable steel rod, spring and rubber cushion, zinc plated |
| 514 | 8302.41.90.31 | Garage door hardware | Steel spring-loaded retaining assemblies, in left or right orientation, consisting of a steel mounting bracket, sliding steel tube, extension spring, steel washer and rivet, with rubber cushion contact pad, zinc plated |
| 515 | 8302.41.90.31 | Garage door hardware | Steel spring-loaded retaining assembly for garage doors, consisting of a steel mounting bracket, sliding steel tube, extension spring, steel washer and rivet, with rubber cushion contact pad, zinc plated |
| 516 | 8302.41.90.31 | Garage door hardware | Steel adjustable top roller mounting brackets for garage doors, with dimensions of at least 2.75 inches by 2.55 inches but not exceeding 3.92 inches by 2.79 inches, with sliding adjustment and bolt/nut assembly, zinc plated |
| 517 | 8302.41.90.31 | Garage door hardware | Steel end bearing bracket assembly for garage door torsion spring system, consisting of L-bracket, bearing flange, ball bearing and hardware (2 bolts and 2 nuts), zinc plated |
| 518 | 8302.41.90.31 | Garage door hardware | Steel bottom corner brackets for garage doors (pair), with riveted milford pin, with dimensions of 75 mm by 180 mm by 2.5 mm, zinc plated |
| 519 | 8302.41.90.31 | Garage door hardware | Steel garage door handle, with overall dimensions of 7.5 inches by 1.5 inches, with mounting holes spaced 6 inches apart, zinc plated |
| 520 | 8302.41.90.31 | Garage door hardware | Stamped steel decorative garage door handle, with dimensions of 11.2 inches by 1.58 inches, black painted |
| 521 | 8302.41.90.31 | Garage door hardware | Cast steel blade tip endlocks for rolling doors, with or without rivets, with dimensions of approximately 1.5 inches by 2 inches by 0.5 inches, zinc plated |
| 522 | 8302.41.90.31 | Garage door hardware | Steel retaining spring leaf kits, consisting of 2 L-shaped steel supports of 9 inches by 1.250 inches by 0.375 inches (zinc plated), 2 curved spring steel leaves of 20 inches by 2 inches by 0.130 inches (black painted) and 8 bolt/nut sets (zinc plated) |
| 523 | 8302.41.90.31 | Garage door hardware | Steel auto latch assembly for garage doors, consisting of 2 steel supports and torsion spring, with overall dimensions of 2 inches by 3.75 inches by 2 inches, zinc plated |
| 524 | 8302.41.90.31 | Garage door hardware | Galvanized steel central support for counterbalance shaft, 11 gauge, with dimensions of 8.84 inches by 5 inches |
| 525 | 8302.41.90.31 | Garage door hardware | Steel wall mounted rail brackets (pair), 13 gauge (0.090 inches), with a length of 18 inches, zinc plated |
| 526 | 8302.41.90.31 | Garage door hardware | Steel adjustable bottom bracket assembly for garage doors, with a 4 mm adjustment slot, with dimensions of 6.25 inches by 5 inches by 0.118 inches, with ball bearing, zinc plated |
| 527 | 8302.41.90.31 | Garage door hardware | Steel retaining spring leaf kit, consisting of 2 L-shaped steel supports of 9 inches by 1.250 inches by 0.375 inches (zinc plated), 2 curved spring steel leaves of 20 inches by 2 inches by 0.130 inches (black painted) and 8 bolt/nut sets (zinc plated) |
| 528 | 8302.41.90.31 | Garage door hardware | Steel garage door bearing bracket for torsion spring system, with press steel ball bearing of 1 inch inside diameter and 2 inches outside diameter, with bracket dimensions of 6.25 inches by 5 inches by 0.118 inches, zinc plated |
| 529 | 8302.41.90.31 | Garage door hardware | Stamped steel decorative garage door plate, with dimensions of 18 inches by 2 inches by 0.25 inches, with three mounting holes, zinc plated and black powder coated |
| 530 | 8302.41.90.31 | Garage door hardware | Steel garage door rollers with stamped steel roller head and steel bearing, with a roller head diameter of at least 1.7 inches but not exceeding 3 inches, with a steel stem diameter of at least 0.43 inches but not exceeding 0.472 inches and with a stem length of at least 3.3 inches but not exceeding 9.5 inches, zinc plated or uncoated |
| 531 | 8302.41.90.31 | Garage door hardware | Steel garage door roller with nylon roller head, with a 6200 series steel ball bearing, with a roller head diameter of 1.8 inches, with a steel stem diameter of 0.43 inches and with a stem length of 7 inches, zinc plated |
| 532 | 8302.41.90.39 | Base metal fittings | Cast iron and carbon steel decorative hardware: spring handles, pull handles, gate handles, knockers, studs, black powder coated |
| 533 | 8302.41.90.39 | Base metal fittings | Carbon steel spring-loaded self-closing gate closure assemblies, single and double drive, for residential and commercial fence gates |
| 534 | 8302.41.90.90 | Base metal fittings | Duplex stainless steel frameless glass panel brackets and clamps of grade 2205, precision cast (investment cast), including deck-mounted base brackets, inline clamps, wall-to-glass brackets, 90-degree corner clamps and adjustable clamps, compatible with a glass thickness of 12 mm, with a length of at least 25.4 mm but not exceeding 104 mm, with a width of at least 25 mm but not exceeding 104 mm and with a height of at least 65.5 mm but not exceeding 184.8 mm, matte black powder coated or satin finished |
| 535 | 9401.71.10 | Seats and chairs | Upholstered reclining seats with steel frames of grade S355, of specification EN 10025-2, formed, CNC machined and welded, with a height of at least 95 cm but not exceeding 110 cm, with a width of at least 70 cm but not exceeding 90 cm, with a depth of at least 70 cm but not exceeding 85 cm and with a frame thickness of at least 2.5 mm but not exceeding 8 mm, zinc plated, electrophoretically coated and/or powder coated |
| 536 | 9401.71.10.10 | Seats and chairs | Upholstered infant and children's dining chairs incorporating cold-rolled steel tubing of grade SPCC, with round tubing of an outer diameter of at least 15.88 mm but not exceeding 31.75 mm, with oval tubing of cross-sectional dimensions of at least 21.56 mm by 35.00 mm but not exceeding 30.06 mm by 44.78 mm, with a wall thickness of at least 0.8 mm but not exceeding 1.5 mm, with component lengths of at least 259.8 mm but not exceeding 1,503 mm, powder coated |
| 537 | 9401.71.10.10 | Seats and chairs | Upholstered single-seat lounge chairs with or without arm rests, with steel tubular frames, with an outer diameter of at least 0.5 inches but not exceeding 1 inch, plated |
| 538 | 9401.71.10.10 | Seats and chairs | Upholstered ottomans with steel tubular frames, with a wall thickness not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch, plated |
| 539 | 9401.71.10.10 | Seats and chairs | Upholstered single seats without backrests, with steel tubular frames, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch, plated |
| 540 | 9401.71.10.10 | Seats and chairs | Upholstered multi-seat chairs with backrests and arm rests, with steel tubular frames, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch |
| 541 | 9401.71.10.10 | Seats and chairs | Upholstered chaise sofas with steel tubular frames, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch, plated |
| 542 | 9401.71.10.10 | Seats and chairs | Upholstered convertible sofas with steel tubular frames, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch, plated |
| 543 | 9401.71.10.10 | Seats and chairs | Upholstered bar-height chairs with or without backrests and arm rests, with steel tubular frames, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch, plated |
| 544 | 9401.71.10.10 | Seats and chairs | Upholstered lounge-height chairs with or without backrests and arm rests, with steel tubular frames, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch, plated |
| 545 | 9401.71.10.10 | Seats and chairs | Upholstered reclining chairs for residential use, with cold-formed welded steel tube frames of grade E235+CR1-KV of specification EN 10305-3, bent and welded, with a tensile strength of at least 230 N/mm² but not exceeding 500 N/mm², with component lengths not exceeding 90 inches, with manual push-back or electrically operated reclining mechanism, uncoated or powder coated |
| 546 | 9401.71.10.10 | Seats and chairs | Upholstered single-seat lounge chairs, accent chairs, and dining chairs with steel tubular frames, for residential use |
| 547 | 9401.71.10.10 | Seats and chairs | Upholstered infant and children's dining chairs with cold-rolled steel tubing frames, powder coated |
| 548 | 9401.71.10.10 | Seats and chairs | Upholstered bar-height and counter-height chairs with steel tubular frames, for residential and hospitality use |
| 549 | 9401.71.10.90 | Seats and chairs | Upholstered height-adjustable office chairs on casters, with steel tubular frames and steel bases, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch |
| 550 | 9401.71.10.90 | Seats and chairs | Upholstered reclining sofas, loveseats and sectionals for residential use, with cold-formed welded steel tube frames of grade E235+CR1-KV of specification EN 10305-3, bent and welded, with a tensile strength of at least 230 N/mm² but not exceeding 500 N/mm², with component lengths not exceeding 90 inches, uncoated or powder coated |
| 551 | 9401.71.10.90 | Seats and chairs | Upholstered reclining chairs with cold-formed welded steel tube frames, manual or electric, for residential use |
| 552 | 9401.71.10.90 | Seats and chairs | Upholstered reclining sofas, loveseats, sectionals, chaise sofas, and convertibles with steel tubular frames |
| 553 | 9401.71.90 | Seats and chairs | Upholstered height-adjustable office chairs on casters, with steel tubular frames and steel bases, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch |
| 554 | 9401.71.90 | Seats and chairs | Upholstered office chairs for residential use, with cold-formed welded steel tube frames of grade E235+CR1-KV of specification EN 10305-3, bent and welded, with a tensile strength of at least 230 N/mm² but not exceeding 500 N/mm², with component lengths not exceeding 90 inches, uncoated or powder coated |
| 555 | 9401.71.90 | Seats and chairs | Upholstered height-adjustable office chairs on casters with steel tubular frames and steel bases |
| 556 | 9403.10.00.10 | Metal furniture | Fireproof/fire-rated filing cabinets of metal for office use |
| 557 | 9403.10.00.10 | Metal furniture | Lateral file cabinets of metal for office use |
| 558 | 9403.10.00.10 | Metal furniture | Vertical file cabinets of metal for office use |
| 559 | 9406.20.00 | Prefabricated buildings | Modular steel building units: portable offices, construction site trailers, temporary classrooms |
| 560 | 9406.20.00 | Prefabricated buildings | Modular steel units for remote workforce camps, data centre modules, and relocatable industrial structures |
| 561 | 9406.90.90 | Prefabricated buildings | Prefabricated steel buildings, supplied as complete unassembled kits, consisting of built-up tapered columns and rafters of specification ASTM A572/A992, rolled W-shape endwall columns and rafters, cold-formed Z-section purlins and girts of specification ASTM A1011/A653 Grade 55 (12 to 16 gauge), cold-formed C/Z eave struts and jambs (10 to 16 gauge), cable bracing of specification ASTM A475, angle flange braces, high-strength bolts of specification ASTM A325/A490, anchor rods and base plates of specification ASTM A36, and roof and wall cladding panels (26 gauge) with aluminum-zinc alloy coating, shop-primed |
| 562 | 9406.90.90.90 | Prefabricated buildings | Prefabricated steel buildings as complete unassembled kits: tapered columns/rafters, cold-formed purlins/girts, bracing, bolts, cladding panels |
Privacy
Information received throughout this submission process is subject to the Access to Information Act and the Privacy Act and is collected under the authority of the Financial Administration Act. Participation in these consultations is voluntary and will have no impacts on services you receive from the Government of Canada. Personal information provided on this form is collected to enable individuals to participate in national and/or international outreach activities, as well as to connect businesses who are seeking remission due to insufficient supply with Canadian manufacturers who self-identify through these consultations.
The collection, use, disclosure and retention of your personal information is in accordance with requirements of the Privacy Act and is further described in the following Personal Information Banks – PSU 938 (Outreach Activities) and PSU 914 (Public Communications). You have the right to access, and request correction of, your personal information. If you have any questions regarding the protection of your personal information, please contact the Department of Finance Canada’s Access to Information and Privacy (ATIP) Coordinator at atip-aiprp@fin.gc.ca. If you are not satisfied with the response to your privacy concern, you have the right to file a complaint with the Office of the Privacy Commissioner of Canada regarding the department’s handling your personal information.