Quantification Methods for the Output-Based Pricing System Regulations – December 2023
December 12, 2023
Introduction
On November 22, 2023, the Regulations Amending the Output-Based Pricing System Regulations and the Environmental Violations Administrative Monetary Penalties Regulations (the Amendments) were published in the Canada Gazette, Part II. The Amendments result from the 2022 review of the Output-Based Pricing System Regulations (OBPS Regulations).
A key change to the OBPS Regulations is the incorporation by reference the Quantification Methods for the Output-Based Pricing System Regulations (OBPS QM) document. The OBPS QM sets out the methods for quantification to be used when quantifying GHGs, the ratio of heat and the quantity of electricity generated, as required under the OBPS.
This change will enable improved harmonization of quantification methods for GHG emissions between the OBPS Regulations and the federal Greenhouse Gas Reporting Program (GHGRP) over time as quantification methods are updated.
The OBPS QM applies to the 2024 and future compliance periods.
How to use the OBPS QM:
- Section 2 provides general quantification rules, including which methods are to be used where there is no prescribed method for an activity.
- Section 3 provides specific quantification rules, including carbon capture and storage and continuous emissions monitoring system methods.
- Section 4 provides detailed quantification requirements per industrial sector.
- Production quantification methods remain in Schedule 3 to the OBPS Regulations.
Below is a list of some key changes that have been made to the prescribed quantification methodologies:
- Adding exceptions for sampling, analysis, and measurement methodology for wastewater emissions throughout section 4.
- Updating “anaerobic wastewater treatment” to “wastewater treatment” throughout section 4.
- Referencing GHGRP instead of WCI method for flaring emissions.
- Referencing GHGRP instead of WCI method for nitric acid industrial process emissions.
Definitions
- Alberta GHG Quantification Methods
- means version 2.3 of the document title Alberta’s Greenhouse Gas Quantification Methodologies, published by the Alberta Government in September 2023.
- CEMS Protocols
- means the document titled Protocols and performance specifications for continuous monitoring of gaseous emissions from thermal power generation and other sources, published by Environment and Climate Change Canada in 2023.
- Directive 017
- means the directive titled Directive 017: Measurement Requirements for Oil and Gas Operations, published by the Alberta Energy Regulator on March 17, 2022, as amended from time to time.
- Directive PNG017
- means the directive titled Directive PNG017: Measurement Requirements for Oil and Gas Operations, published by the Government of Saskatchewan in August 2022, as amended from time to time.
- GHG
- means greenhouse gas set out in Schedule 3 to the Greenhouse Gas Pollution Pricing Act.
- GHGRP 2022/2023
- means the document titled Canada’s Greenhouse Gas Quantification Requirements: Greenhouse Gas Reporting Program, version 6.0, published by Environment and Climate Change Canada in December 2022.
- GHGRP 2024/2025
- means the document titled Canada’s Greenhouse Gas Quantification Requirements: Greenhouse Gas Reporting Program, version 7.0, published by Environment and Climate Change Canada in December 2023.
- IPCC Guidelines
- means the guidelines titled 2006 IPCC Guidelines for National Greenhouse Gas Inventories, published by the Institute for Global Environmental Strategies for the Intergovernmental panel on climate change, as amended from time to time.
- Oil Sands QM
- means the document titled Quantification of Area Fugitive Emissions at Oil Sands Mines, version 2.2, published in June 2023 by the department of Environment and Parks of the Government of Alberta.
- WCI Method
- means the document titled Final Essential Requirements of Mandatory Reporting, published on December 17, 2010, by the Western Climate Initiative, as amended from time to time.
1. Purpose
This document prescribes the methods to quantify GHGs, the ratio of heat and the quantity of electricity generated, as required under the Output-Based Pricing System Regulations (OBPS Regulations).
2. General Quantification Rules
2.1. Quantity of GHGs
For the purposes of paragraphs 17(2)(a) and 20(2)(a) of the OBPS Regulations, the GHG quantification methods are set out in column 3 of the tables in section 4 of this document applicable to the industrial activities engaged in at the covered facility.
For the purposes of paragraphs 17(2)(b) and (c) and 20(2)(b) of the OBPS Regulations, where the specified emissions type or GHGs are not listed in column 1 or 2 of the tables in section 4 of this document applicable to the industrial activities engaged in at the covered facility or where there are no applicable tables in section 4, GHGs are to be quantified in accordance with:
- the GHGRP 2024/2025 if those methods are applicable to the activities engaged in at the covered facility,
- the WCI method, if those methods are applicable to the activities engaged in at the covered facility and are not available in the GHGRP 2024/2025, or
- the IPCC guidelines, if those guidelines are applicable to the activities engaged in at the covered facility and are not available in the GHGRP 2024/2025 or WCI Method.
When calculating GHGs from stationary fuel combustion using GHGRP 2024/2025, section 2.A, note # 6 from the key notes list does not apply.
2.2. Sampling, analysis and measurement requirements
For the purposes of subsection 17(3) and 20(4) of the OBPS Regulations, the sampling, analysis and measurement requirements are set out in column 4 of the tables in section 4 of this document applicable to the industrial activities engaged in at the covered facility.
For the purposes of subsection 17(3) and 20(4) of the OBPS Regulations, where the sampling, analysis and measurement requirements are not listed in column 4 of the tables in section 4 of this document applicable to the industrial activities engaged in at the covered facility or where there are no applicable tables in section 4, the sampling, analysis and measurement requirements are specified in:
- the GHGRP 2024/2025 if those methods are applicable to the activities engaged in at the covered facility,
- the WCI method, if those methods are applicable to the activities engaged in at the covered facility and are not available in the GHGRP 2024/2025, or
- the IPCC guidelines, if those guidelines are applicable to the activities engaged in at the covered facility and are not available in the GHGRP 2024/2025 or WCI Method.
2.3. Missing data
For the purposes of subsection 17(4) and 20(5) of the OBPS Regulations, the missing data methods are set out in column 5 of the tables in section 4 of this document applicable to the industrial activities engaged in at the covered facility.
For the purposes of subsection 17(4) and 20(5) of the OBPS Regulations, where the missing data methods are not listed in column 5 of the tables in section 4 of this document applicable to the industrial activities engaged in at the covered facility or where there are no applicable tables in section 4, the missing data methods are specified in:
- the GHGRP 2024/2025 if those methods are applicable to the activities engaged in at the covered facility,
- the WCI method, if those methods are applicable to the activities engaged in at the covered facility and are not available in the GHGRP 2024/2025, or
- the IPCC guidelines, if those guidelines are applicable to the activities engaged in at the covered facility and are not available in the GHGRP 2024/2025 or WCI Method.
2.4. Conflicting requirements
For a requirement made under GHGRP 2024/2025 in respect of quantification of GHGs, in the event of a conflict between the OBPS Regulations and GHGRP, the OBPS Regulations prevail to the extent of the conflict.
3. Specific Quantification Rules
3.1. Ratio of heat
For the purposes of paragraph 34(1)(b) of the OBPS Regulations, when determining the ratio of heat the following variables are quantified as follows:
HHVi
is the higher heating value of the fossil fuel of type “i” combusted in the facility for the generation of thermal energy during the compliance period determined in accordance with sections 2.D.1 and 2.D.3 of the GHGRP 2024/2025.
QBBk
is the quantity of biomass fuel type “k” combusted in the facility for the generation of thermal energy during the compliance period, determined in accordance with subsection 4(2) of Part 38 of Schedule 3 to the OBPS Regulations and the WCI Method WCI.214.
HHVk
is the higher heating value for biomass fuel type “k” combusted in the facility during the compliance period for the generation of thermal energy in accordance with sections 2.D.1 and 2.D.3 of the GHGRP 2024/2025 and the WCI Method WCI.214.
For the purposes of paragraph 34(1)(c) of the OBPS Regulations, when determining the ratio of heat the following variables are quantified as follows:
HHVi
is the higher heating value of the fossil fuel of type “i” combusted in the facility for the generation of thermal energy during the compliance period, determined in accordance with sections 2.D.1 and 2.D.3 of the GHGRP 2024/2025.
HHVk
is the higher heating value for biomass fuel type “k” combusted in the facility during the compliance period for the generation of thermal energy in accordance with sections 2.D.1 and 2.D.3 of the GHGRP 2024/2025 and WCI Method WCI.214.
For the purposes of subsection 4(2) of Division 3 of Part 38 of Schedule 3 to the OBPS Regulations, as referenced in paragraph 34(1)(b), the quantity of fuel for QFi and QBBk is determined on the following basis:
(a) for a solid fuel, the mass of the fuel combusted, on a wet or dry basis, expressed in tonnes and measured in accordance with section 2.D.2 of the GHGRP 2024/2025;
(b) for a liquid fuel, the volume of the fuel combusted, expressed in kiloliter and measured in accordance with section 2.D.2 of the GHGRP 2024/2025; and
(c) for a gaseous fuel, the volume of the fuel combusted, expressed in standard cubic metres and measured in accordance with section 2.D.2 of the GHGRP 2024/2025.
3.2. Quantity of CO2 captured and stored
For the purposes of subsection 35(1) of the OBPS Regulations, the variable B is determined as follows:
B is the quantity of carbon dioxide (CO2) captured at the covered facility that is stored during the compliance period in a storage project, determined using the quantification method described in section 1 of the GHGRP 2024/2025, expressed in carbon dioxide equivalent (CO2e) tonnes.
3.3. Quantity of electricity generated
For the purposes of subsection 1(2) of Division 2 to Part 38 Schedule 3 to the OBPS Regulations, variables HHVi and HHVj are quantified in accordance with section 2.D.1 and 2.D.3 of the GHGRP 2024/2025.
For the purposes of subsection 4(1) of Division 3 of Part 38 of Schedule 3 to the OBPS Regulations, the following variables are quantified as follows:
QFFj
is the quantity of gaseous, liquid, or solid fuel, as the case may be, type “j” combusted in the facility for electricity generation during the compliance period, determined in accordance with section 4(2) of Division 3 of Part 38 of Schedule 3 to the OBPS Regulations and section 2.D.2 of the GHGRP 2024/2025,
HHVj
is the higher heating value of the gaseous, liquid or solid fuel, as the case may be, type “j” combusted in the facility for electricity generation determined in accordance with sections 2.D.1 and 2.D.3 of the GHGRP 2024/2025,
QBi
is the quantity of biomass fuel type “i” combusted in the facility for electricity generation during the compliance period, determined in accordance with subsection 4(2) of Division 3 of Part 38 of Schedule 3 to the OBPS Regulations and with section 2.D.2 of the GHGRP 2024/2025 and the WCI Method WCI.214, and
HHVi
is the higher heating value for each biomass fuel type “i” combusted in the facility for electricity generation in accordance with sections 2.D.1 and 2.D.3 of the GHGRP 2024/2025 and the WCI Method WCI.214.
For the purposes of subsection 4(2) of Division 3 of Part 38 of Schedule 3 to the OBPS Regulations, the quantity of fuel for QFFj and QBi is determined on the following basis:
(a) for a solid fuel, the mass of the fuel combusted, on a wet or dry basis, expressed in tonnes and measured in accordance with section 2.D.2 of the GHGRP 2024/2025;
(b) for a liquid fuel, the volume of the fuel combusted, expressed in kiloliter and measured in accordance with section 2.D.2 of the GHGRP 2024/2025; and
(c) for a gaseous fuel, the volume of the fuel combusted, expressed in standard cubic metres and measured in accordance with section 2.D.2 of the GHGRP 2024/2025.
3.4. Continuous Emissions Monitoring Systems
For the purposes of the section 25 of the OBPS Regulations, if a continuous emissions monitoring system (CEMS) is used to quantify GHGs, the person responsible for the covered facility must ensure that the system complies with the requirements of the CEMS Protocols.
For the purposes of subsection 45(2) of the OBPS Regulations, for each compliance period during which a person responsible for the covered facility uses a continuous emissions monitoring system, they must comply with the record keeping requirements set out in the CEMS Protocols.
For the purposes of the OBPS Regulations, when the requirements of the CEMS Protocols require any data or records to be kept for at least 3 years, those records must be kept for at least 7 years. This aligns with the record keeping requirements for a person responsible for a covered facility set out in paragraph 187(5) of the Greenhouse Gas Pollution Pricing Act.
For greater certainty, when a CEMS is used to quantify GHGs at a covered facility, any quantity of GHGs that have not been quantified using the CEMS must be included in the total quantity of GHGs from the covered facility calculated in accordance with subsections 17(2) to (4) or 20(2) to (5) of the OBPS Regulations.
4. Quantification of GHGs for Industrial Activities
Part 1: Bitumen and Other Crude Oil Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | Directive 017, Directive PNG017 | GHGRP 2024/2025 2.E |
| Item 2: Flaring emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.C | Directive 017, Directive PNG017 | GHGRP 2024/2025 2.E |
| Item 3: Wastewater emissions from | ||||
| (a) anaerobic and aerobic wastewater treatment | CO2, CH4 and N2O | GHGRP 2024/2025 11.G | GHGRP 2024/2025 11.N.7* | GHGRP 2024/2025 11.O |
| (b) oil-water separators | CH4 | GHGRP 2024/2025 11.H | GHGRP 2024/2025 11.N.8 | GHGRP 2024/2025 11.O |
| Item 4: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exceptions:
*Sampling, analysis and measurement requirements (1) and (2) of section 11.N.7 of GHGRP 2024/2025 are replaced by
(1) You must collect samples representing wastewater influent to the wastewater treatment process, following all preliminary and primary treatment steps (e.g., after grit removal, primary clarification, oil-water separation, dissolved air flotation, or similar solids and oil separation processes). You must collect and analyze samples for COD or BOD5 concentration once each calendar week.
(2) You must measure the flowrate of wastewater entering wastewater treatment process once each calendar week. The flow measurement location must correspond to the location used to collect samples analyzed for COD or BOD5 concentration.
Part 2: Bitumen and Heavy Oil Upgrading
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | Directive 017, Directive PNG017 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions from | ||||
| (a) hydrogen production | CO2 | GHGRP 2024/2025 10.A | GHGRP 2024/2025 10.B | GHGRP 2024/2025 10.C |
| (b) sulphur recovery | CO2 | GHGRP 2024/2025 11.D | GHGRP 2024/2025 11.N.4 | GHGRP 2024/2025 11.O |
| (c) catalyst regeneration | CO2, CH4 and N2O | GHGRP 2024/2025 11.A | GHGRP 2024/2025 11.N.1 | GHGRP 2024/2025 11.O |
| Flaring emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.C | GHGRP 2024/2025 2.D.7 | GHGRP 2024/2025 2.E |
| Item 3: Venting emissions from | ||||
| (a) process vents | CO2 and N2O | GHGRP 2024/2025 11.B | GHGRP 2024/2025 11.N.2 | GHGRP 2024/2025 11.O |
| (b) uncontrolled blowdown | CO2 and N2O | GHGRP 2024/2025 11.K | GHGRP 2024/2025 11.N.2 | GHGRP 2024/2025 11.O |
| Item 4: Wastewater emissions from | ||||
| (a) anaerobic and aerobic wastewater treatment | CO2, CH4 and N2O | GHGRP 2024/2025 11.G | GHGRP 2024/2025 11.N.7* | GHGRP 2024/2025 11.O |
| (b) oil-water separators | CH4 | GHGRP 2024/2025 11.H | GHGRP 2024/2025 11.N.8 | GHGRP 2024/2025 11.O |
| Item 5: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exceptions:
*Sampling, analysis and measurement of wastewater emissions in section 11.N.7 of GHGRP 2024/2025 are replaced by
(1) You must collect samples representing wastewater influent to the wastewater treatment process, following all preliminary and primary treatment steps (e.g., after grit removal, primary clarification, oil-water separation, dissolved air flotation, or similar solids and oil separation processes). You must collect and analyze samples for COD or BOD5 concentration once each calendar week.
(2) You must measure the flowrate of wastewater entering wastewater treatment process once each calendar week. The flow measurement location must correspond to the location used to collect samples analyzed for COD or BOD5 concentration.
Part 3: Petroleum Refining
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Venting emissions from | ||||
| (a) process vent | CO2, CH4 and N2O | GHGRP 2024/2025 11.B | GHGRP 2024/2025 11.N.2 | GHGRP 2024/2025 11.O |
| (b) asphalt production | CO2 and CH4 | GHGRP 2024/2025 11.C | GHGRP 2024/2025 11.N.2 | GHGRP 2024/2025 11.O |
| (c) delayed coking unit | CH4 | GHGRP 2024/2025 11.M | GHGRP 2024/2025 11.M | GHGRP 2024/2025 11.O |
| Item 3: Industrial process emissions from | ||||
| (a) hydrogen production | CO2 | GHGRP 2024/2025 10.A | GHGRP 2024/2025 10.B | GHGRP 2024/2025 10.C |
| (b) catalyst regeneration | CO2, CH4 and N2O | GHGRP 2024/2025 11.A | GHGRP 2024/2025 11.N.1 | GHGRP 2024/2025 11.O |
| (c) sulphur recovery | CO2 | GHGRP 2024/2025 11.D | GHGRP 2024/2025 11.N.4 | GHGRP 2024/2025 11.O |
| (d) coke calcining | CO2, CH4 and N2O | GHGRP 2024/2025 11.J | GHGRP 2024/2025 11.N.9 | GHGRP 2024/2025 11.O |
| Item 4: Flaring emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.C | GHGRP 2024/2025 2.D.7 | GHGRP 2024/2025 2.E |
| Item 5: Leakage emissions | CH4 | GHGRP 2024/2025 11.I | GHGRP 2024/2025 11.I | GHGRP 2024/2025 11.O |
| Item 6: Wastewater emissions from | ||||
| (a) anaerobic and aerobic wastewater treatment | CO2, CH4 and N2O | GHGRP 2024/2025 11.G | GHGRP 2024/2025 11.N.7* | GHGRP 2024/2025 11.O |
| (b) oil-water separators | CH4 | GHGRP 2024/2025 11.H | GHGRP 2024/2025 11.N.8 | GHGRP 2024/2025 11.O |
| Item 7: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exceptions:
*Sampling, analysis and measurement of wastewater emissions in section 11.N.7 of GHGRP 2024/2025 are replace by
(1) You must collect samples representing wastewater influent to the wastewater treatment process, following all preliminary and primary treatment steps (e.g., after grit removal, primary clarification, oil-water separation, dissolved air flotation, or similar solids and oil separation processes). You must collect and analyze samples for COD or BOD5 concentration once each calendar week.
(2) You must measure the flowrate of wastewater entering wastewater treatment process once each calendar week. The flow measurement location must correspond to the location used to collect samples analyzed for COD or BOD5 concentration.
Part 3.1: Surface mining of oil sands and extraction of bitumen
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | Directive 017 or Directive PNG017 | GHGRP 2024/2025 2.E |
| Item 2: Flaring emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.C | GHGRP 2024/2025 2.D.7 | GHGRP 2024/2025 2.E |
| Item 3: Leakage emissions | CO2 and CH4 | Oil Sands QM, section 6 | Oil Sands QM, sections 6 and 7 | Oil Sands QM, sections 6 and 7 |
| Item 4: Wastewater emissions from | ||||
| (a) anaerobic and aerobic wastewater treatment | CO2, CH4 and N2O | GHGRP 2024/2025 11.G | GHGRP 2024/2025 11.N.7* | GHGRP 2024/2025 11.O |
| (b) oil-water separators | CH4 | GHGRP 2024/2025 11.H | GHGRP 2024/2025 11.N.8 | GHGRP 2024/2025 11.O |
| Item 5: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exceptions:
*Sampling, analysis and measurement of wastewater emissions in section 11.N.7 of GHGRP 2024/2025 are replace by
(1) You must collect samples representing wastewater influent to the wastewater treatment process, following all preliminary and primary treatment steps (e.g., after grit removal, primary clarification, oil-water separation, dissolved air flotation, or similar solids and oil separation processes). You must collect and analyze samples for COD or BOD5 concentration once each calendar week.
(2) You must measure the flowrate of wastewater entering wastewater treatment process once each calendar week. The flow measurement location must correspond to the location used to collect samples analyzed for COD or BOD5 concentration.
Part 4: Natural Gas Processing
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | Directive 017 or Directive PNG017 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions from acid gas removal | CO2 | WCI Method WCI.363(c) | WCI Method WCI.364 | WCI Method WCI.365 |
| Item 3: Flaring emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.C | Directive 017, Directive PNG017 | GHGRP 2024/2025 2.E |
| Item 4: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 5: Natural Gas Transmission
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Flaring emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.C | Directive 017 or Directive PNG017 | GHGRP 2024/2025 2.E |
Part 6: Hydrogen Gas Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions | CO2 | GHGRP 2024/2025 10.A | GHGRP 2024/2025 10.B | GHGRP 2024/2025 10.C |
| Item 3: Flaring emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.C | GHGRP 2024/2025 2.D.7 | GHGRP 2024/2025 2.E |
| Item 4: Leakage emissions | CH4 | GHGRP 2024/2025 11.I | GHGRP 2024/2025 11.I | GHGRP 2024/2025 11.O |
| Item 5: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 7: Cement and Clinker Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions | CO2 | GHGRP 2024/2025 4.A | GHGRP 2024/2025 4.B | GHGRP 2024/2025 4.C |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 8: Lime Manufacturing
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions | CO2 | GHGRP 2024/2025 3.A | GHGRP 2024/2025 3.B | GHGRP 2024/2025 3.C |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 9: Glass Manufacturing
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions | CO2 | WCI Method WCI.143 | WCI Method WCI.144 | WCI Method WCI.145 |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 10: Gypsum Product Manufacturing
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 11: Mineral Wool Insulation Manufacturing
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions | CO2 | WCI Method WCI.183 | WCI Method WCI.184 | WCI Method WCI.185 |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 12: Brick Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions | CO2 | WCI Method WCI.183 | WCI Method WCI.184 | WCI Method WCI.185 |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 13: Ethanol Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 14: Furnace Black Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions | CO2 | WCI Method WCI.303(b) | WCI Method WCI.304(b) | WCI Method WCI.305 |
| Item 3: Venting emissions | CO2, CH4 and N2O | GHGRP 2024/2025 11.B | GHGRP 2024/2025 11.N.2 | GHGRP 2024/2025 11.O |
| Item 4: Leakage emissions | CH4 | GHGRP 2024/2025 11.I(1) | GHGRP 2024/2025 11.I(1) | GHGRP 2024/2025 11.O |
| Item 5: Industrial product use emissions | SF6 and PFC | WCI Method WCI.233 | WCI Method WCI.234 | WCI Method WCI.235 |
| Item 6: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 15: 2–methylpentamethylenediamine (MPMD) Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions | CO2 | WCI Method WCI.133 | WCI Method WCI.134 | WCI Method WCI.135 |
| Item 3: Industrial product use emissions | SF6 and PFC | WCI Method WCI.233 | WCI Method WCI.234 | WCI Method WCI.235 |
| Item 4: Flaring emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.C | GHGRP 2024/2025 2.D.7 | GHGRP 2024/2025 2.E |
| Item 5: Leakage emissions | CH4 | GHGRP 2024/2025 11.I | GHGRP 2024/2025 11.I | GHGRP 2024/2025 11.O |
| Item 6: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 16: Nylon Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 17: Petrochemicals Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions | CO2 | WCI Method WCI.303(b) | WCI Method WCI.304(b) | WCI Method WCI.305 |
| Item 3: Venting emissions | CO2, CH4 and N2O | GHGRP 2024/2025 11.B | GHGRP 2024/2025 11.N.2 | GHGRP 2024/2025 11.O |
| Item 4: Flaring emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.C | Directive 017, Directive PNG017 | GHGRP 2024/2025 2.E |
| Item 5: Leakage emissions | CH4 | GHGRP 2024/2025 11.I(1) | GHGRP 2024/2025 11.I(1) | GHGRP 2024/2025 11.O |
| Item 6: Wastewater emissions | CO2, CH4 and N2O | GHGRP 2024/2025 11.G | GHGRP 2024/2025 11.N.7* | GHGRP 2024/2025 11.O |
| Item 7: Industrial product use emissions | SF6 and PFC | WCI Method WCI.233 | WCI Method WCI.234 | WCI Method WCI.235 |
| Item 8: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exceptions:
*Sampling, analysis and measurement of wastewater emissions in section 11.N.7 of GHGRP 2024/2025 are replaced by
(1) You must collect samples representing wastewater influent to the wastewater treatment process, following all preliminary and primary treatment steps (e.g., after grit removal, primary clarification, oil-water separation, dissolved air flotation, or similar solids and oil separation processes). You must collect and analyze samples for COD or BOD5 concentration once each calendar week.
(2) You must measure the flowrate of wastewater entering wastewater treatment process once each calendar week. The flow measurement location must correspond to the location used to collect samples analyzed for COD or BOD5 concentration.
Part 18: Vaccine Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial product use emissions | SF6 | WCI Method WCI.233 | WCI Method WCI.234 | WCI Method WCI.235 |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 19: Scrap-based Steel Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions from | ||||
| (a) electric arc furnace | CO2 | GHGRP 2024/2025 6.A.5 | GHGRP 2024/2025 6.C | GHGRP 2024/2025 6.D |
| (b) argon-oxygen decarburization vessel | CO2 | GHGRP 2024/2025 6.A.6 | GHGRP 2024/2025 6.C | GHGRP 2024/2025 6.D |
| (c) ladle furnace | CO2 | GHGRP 2024/2025 6.A.9 | GHGRP 2024/2025 6.C | GHGRP 2024/2025 6.D |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 20: Integrated Steel Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions from | ||||
| (a) basic oxygen furnace | CO2 | GHGRP 2024/2025 6.A.2* | GHGRP 2024/2025 6.C | GHGRP 2024/2025 6.D |
| (b) coke oven battery | CO2 | GHGRP 2024/2025 6.A.3* | GHGRP 2024/2025 6.C | GHGRP 2024/2025 6.D |
| (c) direct reduction furnace | CO2 | GHGRP 2024/2025 6.A.7 | GHGRP 2024/2025 6.C | GHGRP 2024/2025 6.D |
| (d) electric arc furnace | CO2 | GHGRP 2024/2025 6.A.5 | GHGRP 2024/2025 6.C | GHGRP 2024/2025 6.D |
| (e) blast furnace | CO2 | GHGRP 2024/2025 6.A.8* | GHGRP 2024/2025 6.C | GHGRP 2024/2025 6.D |
| (f) ladle furnace | CO2 | GHGRP 2024/2025 6.A.9 | GHGRP 2024/2025 6.C | GHGRP 2024/2025 6.D |
| (g) argon-oxygen decarburization vessel | CO2 | GHGRP 2024/2025 6.A.6 | GHGRP 2024/2025 6.C | GHGRP 2024/2025 6.D |
| Item 3: Wastewater emissions | CO2, CH4 and N2O | GHGRP 2024/2025 11.G | GHGRP 2024/2025 11.N.7** | GHGRP 2024/2025 11.O |
| Item 4: Industrial product use emissions | SF6 and PFC | WCI Method WCI.233 | WCI Method WCI.234 | WCI Method WCI.235 |
| Item 5: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
| Item 6: Leakage emissions from coal storage | CH4 | WCI Method WCI.103 | WCI Method WCI.104 | WCI Method WCI.105 |
Exceptions:
*For the purposes of calculating CO2 industrial process emissions in section 6.A of the GHGRP 2024/2025:
- BOG x CBOG is equal to zero in equation 6-3
- COG x CCOG is equal to zero in equation 6-4
- BG x CBG is equal to zero in equation 6-9
**Sampling, analysis and measurement requirements (1) and (2) of section 11.N.7 of GHGRP 2024/2025 are replaced by
(1) You must collect samples representing wastewater influent to the wastewater treatment process, following all preliminary and primary treatment steps (e.g., after grit removal, primary clarification, oil-water separation, dissolved air flotation, or similar solids and oil separation processes). You must collect and analyze samples for COD or BOD5 concentration once each calendar week.
(2) You must measure the flowrate of wastewater entering wastewater treatment process once each calendar week. The flow measurement location must correspond to the location used to collect samples analyzed for COD or BOD5 concentration.
Part 21: Iron Ore Pelletizing
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions (induration furnace) | CO2 | GHGRP 2024/2025 6.A.1 | GHGRP 2024/2025 6.C | GHGRP 2024/2025 6.D |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 22: Metal Tube Manufacturing
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 23: Base Metal Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4, and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions from | ||||
| (a) lead production | CO2 | GHGRP2024/2025 13.A* | GHGRP 2024/2025 13.B | GHGRP 2024/2025 13.C |
| (b) zinc production | CO2 | GHGRP 2024/2025 13.A* | GHGRP 2024/2025 13.B | GHGRP 2024/2025 13.C |
| (c) copper and nickel production | CO2 | GHGRP 2024/2025 13.A* | GHGRP 2024/2025 13.B | GHGRP 2024/2025 13.C |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exception:
*For the purposes of calculating industrial process emissions using section 13.A of GHGRP 2024/2025, de minimis emissions must meet the requirements of section 23 of the OBPS Regulations.
Part 24: Potash Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 24.1: Production of Evaporated Salt
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 25: Coal Mining
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Leakage emissions from | ||||
| (a) coal storage | CH4 | WCI Method WCI.103 | WCI Method WCI.104 | WCI Method WCI.105 |
| (b) underground coal mining | CH4 | WCI Method WCI.253 | WCI Method WCI.254 | WCI Method WCI.255 |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
For the purpose of item 2 of Table 1 to this Part, the CH4 leakage emissions from surface coal mining are quantified by multiplying the quantity of coal extracted by the applicable emission factor set out in column 3 of Table 2 to this Part according to the province of extraction set out in column 1 and the coal type set out in column 2 of Table 2.
| Province (column 1) | Coal Type (column 2) | Emission Factor (tonnes of CH4/ tonnes of coal) (column 3) |
|---|---|---|
| Item 1: Nova Scotia | Bituminous | 7 x 10–5 |
| Item 2: New Brunswick | Bituminous | 7 x 10–5 |
| Item 3: Saskatchewan | Lignite | 7 x 10–5 |
| Item 4: Alberta | Bituminous | 5.5 x 10–4 |
| Item 5: Alberta | Sub-bituminous | 2 x 10–4 |
| Item 6: British Columbia | Bituminous | 8.6 x 10–4 |
Part 26: Production of Metals or Diamonds
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 27: Char Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 28: Activated Carbon Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 29: Nitrogen-based Fertilizer Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions from | ||||
| (a) nitric acid | CO2, CH4 and N2O | GHGRP 2024/2026 9.A and 9.B* | GHGRP 2024/2025 9.C** | GHGRP 2025/2026 9.D |
| (b) ammonia steam reforming | CO2 | GHGRP 2024/2025 8.A*** | GHGRP 2024/2025 8.B | GHGRP 2024/2025 8.C |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exceptions:
* For the purposes of calculating GHGs from industrial process emissions from nitric acid in section 9.A and 9.B of GHGRP 2024/2025, section 9.A of GHGRP 2022/2023 may be used instead for the 2024 compliance period.
** For the purposes of sampling, analysis and measurement of industrial process emissions from nitric acid in section 9.C of GHGRP 2024/2025, section 9.B of GHGRP 2022/2023 may be used instead for the 2024 compliance period.
*** For the purposes of calculating industrial process emissions from ammonia production, do not subtract the quantity of CO2 consumed in the production of urea from the total reported industrial process emissions. Equation 8-5 in section 8.A of GHGRP 2024/2025 is therefore not applicable.
Part 30: Industrial Potato Processing
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Wastewater emissions | CO2, CH4 and N2O | GHGRP 2024/2025 11.G | GHGRP 2024/2025 11.N.7* | GHGRP 2024/2025 11.O |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exceptions:
*Sampling, analysis and measurement requirements (1) and (2) of section 11.N.7 of GHGRP 2024/2025 are replaced by
(1) You must collect samples representing wastewater influent to the wastewater treatment process, following all preliminary and primary treatment steps (e.g., after grit removal, primary clarification, oil-water separation, dissolved air flotation, or similar solids and oil separation processes). You must collect and analyze samples for COD or BOD5 concentration once each calendar week.
(2) You must measure the flowrate of wastewater entering wastewater treatment process once each calendar week. The flow measurement location must correspond to the location used to collect samples analyzed for COD or BOD5 concentration.
Part 31: Industrial Oilseed Processing
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Wastewater emissions | CO2, CH4 and N2O | GHGRP 2024/2025 11.G | GHGRP 2024/2025 11.N.7* | GHGRP 2024/2025 11.O |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exceptions:
*Sampling, analysis and measurement requirements (1) and (2) of section 11.N.7 of GHGRP 2024/2025 are replaced by
(1) You must collect samples representing wastewater influent to the wastewater treatment process, following all preliminary and primary treatment steps (e.g., after grit removal, primary clarification, oil-water separation, dissolved air flotation, or similar solids and oil separation processes). You must collect and analyze samples for COD or BOD5 concentration once each calendar week.
(2) You must measure the flowrate of wastewater entering wastewater treatment process once each calendar week. The flow measurement location must correspond to the location used to collect samples analyzed for COD or BOD5 concentration.
Part 32: Alcohol Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Wastewater emissions | CO2, CH4 and N2O | GHGRP 2024/2025 11.G | GHGRP 2024/2025 11.N.7* | GHGRP 2024/2025 11.O |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exceptions:
*Sampling, analysis and measurement requirements (1) and (2) of section 11.N.7 of GHGRP 2024/2025 are replaced by
(1) You must collect samples representing wastewater influent to the wastewater treatment process, following all preliminary and primary treatment steps (e.g., after grit removal, primary clarification, oil-water separation, dissolved air flotation, or similar solids and oil separation processes). You must collect and analyze samples for COD or BOD5 concentration once each calendar week.
(2) You must measure the flowrate of wastewater entering wastewater treatment process once each calendar week. The flow measurement location must correspond to the location used to collect samples analyzed for COD or BOD5 concentration.
Part 33: Wet Corn Milling
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Wastewater emissions | CO2, CH4 and N2O | GHGRP 2024/2025 11.G | GHGRP 2024/2025 11.N.7* | GHGRP 2024/2025 11.O |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exceptions:
*Sampling, analysis and measurement requirements (1) and (2) of section 11.N.7 of GHGRP 2024/2025 are replaced by
(1) You must collect samples representing wastewater influent to the wastewater treatment process, following all preliminary and primary treatment steps (e.g., after grit removal, primary clarification, oil-water separation, dissolved air flotation, or similar solids and oil separation processes). You must collect and analyze samples for COD or BOD5 concentration once each calendar week.
(2) You must measure the flowrate of wastewater entering wastewater treatment process once each calendar week. The flow measurement location must correspond to the location used to collect samples analyzed for COD or BOD5 concentration.
Part 34: Citric Acid Production
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 35: Sugar Refining
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 35.1: Production of Malt
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Wastewater emissions | CO2, CH4 and N2O | GHGRP 2024/2025 11.G | GHGRP 2024/2025 11.N.7* | GHGRP 2024/2025 11.O |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exceptions:
*Sampling, analysis and measurement requirements (1) and (2) of section 11.N.7 of GHGRP 2024/2025 are replaced by
(1) You must collect samples representing wastewater influent to the wastewater treatment process, following all preliminary and primary treatment steps (e.g., after grit removal, primary clarification, oil-water separation, dissolved air flotation, or similar solids and oil separation processes). You must collect and analyze samples for COD or BOD5 concentration once each calendar week.
(2) You must measure the flowrate of wastewater entering wastewater treatment process once each calendar week. The flow measurement location must correspond to the location used to collect samples analyzed for COD or BOD5 concentration.
Part 36: Pulp and Paper Production
For the purposes of the table, GHGs from stationary fuel combustion emissions from biomass fuels may be quantified using equations 2-1, 2-2, 2-6, 2-7, 2-11, 2-12 or 2-13 of the GHGRP 2024/2025, if applicable.
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions from | ||||
| (a) boiler, thermal oxidizer, direct-fired turbine, engine, gasifier or any other combustion device that generates heat, steam or energy | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B, except for biomass fuels, other than those set out in table 2-4 and 2-12 of the GHGRP, use the emission factors provided in table 20-2 of WCI Method WCI.20a | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| (b) recovery boiler | CO2, CH4 and N2O | For fossil fuels, GHGRP 2024/2025, sections 2.A and 2.B and for pulping liquor, WCI Method WCI.213(c) a | For fossil fuels, GHGRP 2024/2025 2.D.1 to 2.D.4 and for pulping liquor, WCI Method WCI.214 | GHGRP 2024/2025 2.E and for pulping liquor, WCI Method WCI.215 |
| (c) lime kiln | CO2 | GHGRP 2024/2025 2.A | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| (d) lime kiln | CH4 and N2O | GHGRP 2024/2025 2.B, except use the default emission factors for lime kilns set out in Table 210-1 of WCI Method WCI.213a | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions: addition of carbonate compound into a lime kiln | CO2 | GHGRP 2024/2025 12.A.2 | GHGRP 2024/2025 12.B | GHGRP 2024/2025 12.C |
| Item 3: Wastewater emissions | CO2, CH4 and N2O | GHGRP 2024/2025 11.G | GHGRP 2024/2025 11.N.7* | GHGRP 2024/2025 11.O |
| Item 4: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
a For the combustion of biomass fuels where CH4 and N2O emission factors are not prescribed, the IPCC Guidelines must be used to estimate those emissions.
Exceptions:
*Sampling, analysis and measurement requirements (1) and (2) of section 11.N.7 of GHGRP 2024/2025 are replaced by
(1) You must collect samples representing wastewater influent to the wastewater treatment process, following all preliminary and primary treatment steps (e.g., after grit removal, primary clarification, oil-water separation, dissolved air flotation, or similar solids and oil separation processes). You must collect and analyze samples for COD or BOD5 concentration once each calendar week.
(2) You must measure the flowrate of wastewater entering wastewater treatment process once each calendar week. The flow measurement location must correspond to the location used to collect samples analyzed for COD or BOD5 concentration.
Part 37: Main Assembly of Vehicles
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial product use emissions | HFC | WCI Method WCI.43(d) | WCI Method WCI.44 | WCI Method WCI.45 |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 38: Electricity Generation
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2 CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4* | GHGRP 2024/2025 2.E |
| Item 2: Leakage emissions from coal storage | CH4 | WCI Method WCI.103 | WCI Method WCI.104 | WCI Method WCI.105 |
| Item 3: Industrial process emissions from acid gas scrubbers and acid gas reagent | CO2 | GHGRP 2024/2025 7.C | GHGRP 2024/2025 7.D | GHGRP 2024/2025 7.E |
| Item 4: Industrial product use emissions from | ||||
| (a) electrical equipment | SF6 and PFC | WCI Method WCI.233 | WCI Method WCI.234 | WCI Method WCI.235 |
| (b) cooling units | HFC | WCI Method WCI.43(d) | WCI Method WCI.44 | WCI Method WCI.45 |
| Item 5: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exceptions:
*Where the Regulations Limiting Carbon Dioxide Emissions from Natural Gas-fired Generation of Electricity apply to a unit at a covered facility, the person responsible for the facility may use the specific standards prescribed in sections 14, 18, and 19 of those regulations for sampling the higher heating value, carbon content and natural gas in place of the standards set out in sections 2.D.1 to 2.D.4 of GHGRP 2024/2025, while otherwise following the guidance set out in sections 2.D.1 to 2.D.4 of GHGRP 2024/2025.
Part 39: Production of wood products
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 40: Aluminium production from alumina
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions from | ||||
| (a) pre-baked anode consumption | CO2 | GHGRP 2024/2025 5.A.1 | GHGRP 2024/2025 5.B | GHGRP 2024/2025 5.C |
| (b) Søderberg electrolysis cells | CO2 | GHGRP 2024/2025 5.A.2 | GHGRP 2024/2025 5.B | GHGRP 2024/2025 5.C |
| (c) anode effects | PFC | GHGRP 2024/2025 5.A.7 | GHGRP 2024/2025 5.B | GHGRP 2024/2025 5.C |
| (d) carbonate use | CO2 | WCI Method WCI.183 | WCI Method WCI.184 | WCI Method WCI.185 |
| Item 3: Industrial product use emissions | SF6 and HFC | GHGRP 2024/2025 5.A.8 and WCI Method WCI.43(d) | GHGRP 2024/2025 5.B and WCI Method WCI.44 | GHGRP 2024/2025 5.C and WCI Method WCI.45 |
| Item 4: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 41: Production of baked anodes - Aluminium
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions from | ||||
| (a) anode and cathode baking | CO2 | GHGRP 2024/2025 5.A.3, 5.A.4 and 5.A.5 | GHGRP 2024/2025 5.B | GHGRP 2024/2025 5.C |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 42: Production of calcined petroleum coke - Aluminium
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial process emissions from | ||||
| (a) green coke calcination | CO2 | GHGRP 2024/2025 5.A.6 | GHGRP 2024/2025 5.B | GHGRP 2024/2025 5.C |
| Item 3: Industrial product use emissions | HFC | WCI Method WCI.43(d) | WCI Method WCI.44 | WCI Method WCI.45 |
| Item 4: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 43: Production of alumina from bauxite
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial product use emissions | HFC | WCI Method WCI.43(d) | WCI Method WCI.44 | WCI Method WCI.45 |
| Item 3: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Part 44: Production of pneumatic tires
| Specified Emission Types (column 1) | GHGs (column 2) | Method for Calculating GHGs (column 3) | Sampling, Analysis and Measurement Requirements (column 4) | Method for Estimating Missing Analytical Data (column 5) |
|---|---|---|---|---|
| Item 1: Stationary fuel combustion emissions | CO2, CH4 and N2O | GHGRP 2024/2025, sections 2.A and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4 | GHGRP 2024/2025 2.E |
| Item 2: Industrial product use emissions | HFC | WCI Method WCI.43(d) | WCI Method WCI.44 | WCI Method WCI.45 |
| Item 3: Wastewater emissions | CO2, CH4 and N2O | GHGRP 2024/2025 11.G | GHGRP 2024/2025 11.N.7* | GHGRP 2024/2025 11.O |
| Item 4: On-site transportation emissions | CO2, CH4 and N2O | GHGRP 2024/2025 2.A.1.a, 2.A.2.e and 2.B | GHGRP 2024/2025 2.D.1 to 2.D.4, and 2.D.6 | GHGRP 2024/2025 2.E |
Exceptions:
*Sampling, analysis and measurement requirements (1) and (2) of section 11.N.7 of GHGRP 2024/2025 are replaced by
(1) You must collect samples representing wastewater influent to the wastewater treatment process, following all preliminary and primary treatment steps (e.g., after grit removal, primary clarification, oil-water separation, dissolved air flotation, or similar solids and oil separation processes). You must collect and analyze samples for COD or BOD5 concentration once each calendar week.
(2) You must measure the flowrate of wastewater entering wastewater treatment process once each calendar week. The flow measurement location must correspond to the location used to collect samples analyzed for COD or BOD5 concentration.
Page details
- Date modified: